JD900CK2CC General Electric Range - Instructions

Really simple. shut off breakers. checked the breakers were off. then checked again (this is 220V power to the element).
Undid the 2 nuts holding the old element in place. Pulled out the element into the oven space an inch or two.
Used pliers to pull the contacts out from the old element (not by the wires folks). reversed the process and I was done!

RE: 2 yr. old GE double wall oven with convection option in upper oven, non-convection in lower oven: baked goods were not browning, were undercooked or burned. Tested both ovens on regular bake setting using 2 oven thermometers. Set ovens for 350. Although after 10 min both ovens beeped "ready", the oven thermometers actually read 200 - then would swing up as high as 500 and as low as 200 during the 20 min test period. Decided to first replace top oven sensor only, just in case it really was a more expensive control panel problem. It was a bit awkward to reach back there with the oven door in the way, but I have long arms! Aimed my flashlight, removed nuts with a socket wrench, pulled out the sensor, popped the clip and the old sensor easily separated from its connection. Snapped on the new sensor, pushed it back in and reset the nuts. Easy. Set the oven for 350 and tested again with 2 oven thermometers for 45 min. Voila! The oven thermometers read exactly 350 when the oven beeped "ready" and it stayed at 350 throughout the entire 45 min retest period with only a 3 degree variation both up and down. What a great improvement! Immediately went online to Parts Select and ordered another sensor for the bottom oven which was having the same problem. Fixed both ovens all for under $30 - and just in time for Christmas cookies! Don't want to know what the repair guy would have charged.......Merry Christmas!

Very easy to replace. So easy even a man can do it.

Remove two screws hold cook top down: prop it open with piece of wood. (TURN OFF POWER TO RANGE FIRST!). Carefully make diagram of where wires go: remove and replace.. piece of cake!

Loosen the screws to the bake element. Carefully pull out old element until wires are exposed. Pop off the clips from wires to heating element (leaving clips on the wires). Attach clips to new heating element. Screw back into place. Piece of cake!

Remove the top back panel to expose the switch. Remove the switch knob & mounting bezel and then unscrew the 2 mounting screws from the front. Replace the wires one by one and follow the enclosed directions in the event that this is an upgrade for an older switch. Remount the switch from the front and replace the back panel.

1.Move range in position to access electrical wall disconnect and unplug. 2.Remove two 5/16 screws (located under top fwd. edge of cook top, Lift entire top assy up from front and prop with appropriate device(short 2x4 about18 inches long works well) 3.Remove two small phillips screws securing two metallic keeper devices holding burner assy in place. This should allow burner assy to be removed.4.Disconnect electrical spade connectors from ceramic terminal blocks on old burner assy.CAUTION: [SPADE CONNECTORS FIT TIGHTLY DO NOT PULL ON WIRES USE PRYING FORCE WITH FLAT SCREWDRIVER DIRECTLY ON TERMINAL].Remove connectors one at a time re-connecting to same location on new assy. Reassemble in reverse order.

I turned off the breaker, removed the control knobs from all of the burners there are plastic knots on each control knob that needs to be removed (once loosened they can easily be turned by hand). You can then just lift the out piece off. You need to remove 4 knots to release the control panel so you can access the control know. I removed the 2 screws in the old control know, there are 4 wires that need to be pulled to disconnect. I wrote down the order in which the colored wires were connected . I then removed the old part and reversed the process

The cooktop is just set in the counter with no fasteners. I shut off the power and lifted the unit out. Ten small screws held the top to the body. After removal, I took a picture to have a wiring reference. I disconnected five wires with push-on terminals, then removed two Tinnerman nuts with needle-nose pliers. The failed burner was free to remove. There were two mounting ears on the bottom of the burner at positions 12 and 48 as stamped on the bottom. I transferred the mounting ears to the new burner, one screw each. I then positioned the new burner and secured with the two Tinnerman nuts, replaced the five wires, screwed the top back on and slipped the unit into the counter. Done.

Turn off the power to the oven. (There should be a circuit breaker in the main power panel dedicated to just the oven) (the oven should be cool to the touch).
Open and remove the door by pulling it up and off the hinges (this is best accomplished with a helper).
Remove the racks (wire shelves).
Remove the two 1/4" mounting screws that secure the heating element to the back and the two screws that secure the element to the top of the oven..
Gently pull the wires out and disconnect them from the heating element.
Now reverse the process.
Connect the wires to the new heating element in the same fashion as they came off.
Push the wires and heating element back in place and secure with the four screws.
Replace the wire racks (shelves).
Replace the door (again, this is best accomplished with a helper).
Turn the power back on.
Run a test of the broiler to make sure the repair was completed properly.
voila!

Turned power off to oven
Unscrewed broiler nuts (total of 4)
Pulled Broiler out from back of stove
Disconnected wires
Reconnected wire
Remounted broiler and replaced bolts
Turned power back on

Disconnect stove electrical connection. Removed 2 bolts common to the upper stove top cover. Disconnected 4 wires from burner element along with 2 retaining clips.
Removed burner element and replaced with new element. Reinstalled 4 wires and 2 retaining clips. Lowered stove top cover and reinstalled 2 bolts. Connect stove electrical to wall outlet. Turn on burner element and verify that it works.

Removed old switch, put metal jumper from old switch to new one and connected wires to the new one . Reinstalled. Works great.

Turned off power. Opened range door, removed 2 screws that held top in place. Took a photo of the existing wiring for reference. Removed old burner. Be careful with spacers & springs. If dropped, they will be hard to locate in the insulation. Replaced wiring connectors & verified proper location with photo. Closed cover, replaced 2 screws & turned on circuit breaker.

Removed old element with a socket wrench. Replaced new element with socket wrench. Pretty easy!