JCSP38GT1BB General Electric Range - Instructions

Unplugged the stove. Unscrewed the element. opened the rear cover to reach wires. Passed wires through the slot and connected the element. Screwed the element in place. Reinstalled the rear cover. Plugged the stove and pushed it back to place. Tested the oven, it worked.

I followed the directions in the video on the website. The repair was so easy!! I simply unscrewed the screws holding the element in place at the back of the oven, pulled the wires out. This did take a little bit of time, as I didn't want to pull the wire off of the element and lose it in the back of the oven, but I was able to eventually work it free from the insulation and make the connectors visible. I slid off the old element, slid the wires back on to the new one and pushed them back into the wall of the oven and replaced the screws. Works like a charm!! I will definitely use your website for other appliance repairs!!

Pulled oven from wall, Unplugged oven from outlet, Took 5/16 nut driver pulled back cover off oven to expose the quick connect wires, Pulled wires off old element, Opened oven door took the 2 screws off bracket on back of oven, Removed old element, Put new element in place, Put the 2 wires back on, Buttoned back up check to see if worked it did ((:

First I unplugged the stove. I then removed the two screws that held the element in place. I then pulled the element out about four inches to expose the connection. I disconnected the two wires, removed the element and replaced it with the new one. I then reassembled the oven in reverse order. It was very simple.

Very simple. Two small hex shaped screws hold the unit to the back of the stove. Remove those with a small socket wrench. Rachet type makes the job easier. Gently pull the element from the back of the stove. Remove the two push-on wires from the element. They simple pull off. The elements have supporting feet toward the front. Those must be down to rest the element on the bottom of the stove. Replace the push-on wires, push the element back into the holes in the rear of the stove and screw the small hex shaped screws back into the oven wall. The job is done.

pulled out oven, unplugged power. Removed back cover for element, disconnect old element. Moved to front of oven and removed the two screws that held the old element,removed old element. Installed new element, connect element, installed cover, reconnect power.

Took out the hexagon screws, used pliers to pull the connecting ends apart, slid in the new element in to the connecting slots, reattached to screws, turned on the oven to see if it would heat up and it did. It was really easy. I had waited for a week to get the part from my local Sears parts house. You sent it out and I had it in 3 days. They still don't have the part. Thanks so much.

1. Turned breaker to the oven to the off position.
2. Removed screws from back of oven-This was the most difficult part of the entire process!
3. Pull out element about 3", then tugged a little harder to expose the wiring.
4. Unhooked wiring from element.
All of this took about 15 minutes.
When new one arrived (less than 48 hours), I did the reverse of the above. This took about 6 minutes replace with new element. Thanks so much!

Remove dthe two screws and removed the element. Put the new element in and replaced the terminals and screws. Partselected is the fastest shippers on the net.

As others have described, the removal of the old bake element is easy, just undo screws in the mount holding it to the inside wall of oven and pull out, then disconnect wires.

The first thing I faced unique is that some of the old element melted on the walls of my oven. After scrubbing extensively, it was obvious that the majority of the melted element was permanently fused with the oven wall--although it doesn't seem to have affected oven performance so far.

Next since my range was made in 1982, the replacement bake element didn't exactly fit my unit. Several adjustments had to be made. The size and fuctionality of the new bake element matched my oven, however the wire connections and the oven wall mounting bracket and the spacing of the two ends of the element as it went thru the oven wall were very different and required extensive modifications.

I used the old mounting bracket from the old melted element to attach the new element since my oven wall opening and mounting holes matched the old element mount--NOT the new element mount. This required removing the old mount from the old element by means of a vice, hacksaw and wirecutters. It was necessary to examine the old element mount very carefully before I hacksawed it off the old element as it must be reconfigured onto the new element. It will be bent up somewhat while removing---be careful.

Then I reattached the old mount on the new element. This required carefully bending the new element ends to receive the old mount as they were spread too far apart in the new element configuration. After much trial and error bending with several types of wirecutters the old mount was secured to the new element and installed into the oven.

Now a new problem appeared--the element ends now stuck too far into the back wall of the oven, making them dangerously close to touching the exterior of the rear of the oven and remember these are bare, hot electric connections! Much time in trial bendings and repositioning of the new element with the old mount finally resulted in a successful mounting with the old mount and the new element in a way that safely kept the bare wire connections within the rear oven walls.

A final problem was encountered when the new element came with slide-on wire connectors while my old element had screws and holes to connect the wires together. I found a drill bit the size of the required screws and drilled holes in the new element's wire slide-on connectors so that I could use the screw connector system of my old element to connect my new element's wires together. It all worked and the oven is functional.

the only challenging thing realizing that the screws in the back weren't for a screw driver, they were for a very small wrench. Since I didn't have such a tool, I just used vice grips. It all went well though. The oven currently heats to 400 degrees in 7.5 min. I am quite happy.

Removed the two screws pulled out the old element and slid the new element in and put the screws back in. I used it that night to bake supper

Turned off circuit breaker for Range. Removed the 2 screws holding element and pulled wires attached to the element through holes. Disconnected the wires and attached new element. Had problem with one wire springing back into hole used paper clip to fish it back out of hole and then connected 2nd wire to heating element. Turned breaker back on and tested. Baked a cake. MMMMMMMM.

I read the "easy to repair" story after I ordered my part and I felt like I coud do this on my own. (Female not much experience in repairs) I shut off circuit breaker...proceeded to take out element...could not get it to easiler come off...so I made the mistake of cutting the wire because it looked like that's what I needed to do. WORD TO THE WISE...there are clamps that actually pull off the element..just need to pull a little. So my "easy" project was made more difficult because I didn't know this up front. Otherwise it would have been a breeze. I had to go to the hardware store and but new clamps and attach to the cut wire. Good news is my oven is now working and Parts.com was fast, cheaper than the GE parts place and great service.

This was really easy considering what it would have cost to have a repair person come and do it - not to mention the wait time. I had to hunt around a little bit to find the right socket, but once I had that, I unscrewed the bolts in the back and slide the element out. TIP: make sure you turn off the electricity!!!!!!!!! The wires were a little stuck, but the oven is 11 years old, so it's to be expected. One of the wires came off behind the oven, but I used needle nose pliers and fished around until I grabbed it. I detached the wires, attached the new ones, turned the electricity on and it's been baking Christmas cookies ever since. BTW - the part came in 3 days. I was sooo happy I didn't have to wait for a repair person. Thanks for all of you who posted your comments online. That was just the encouragement I needed to try it myself!