JCKP70SM2SS General Electric Wall Oven - Overview
Sections of the JCKP70SM2SS
[Viewing 5 of 5]
Keep searches simple, eg. "belt" or "pump".
Temperature Sensor
PartSelect #: PS10059162
Manufacturer #: WB21X22134
The temperature sensor detects the temperature within the oven cavity. If your oven is too hot, not heating evenly, or has little to no heat when baking, you may need to replace the temperature sensor...
$36.73
Special Order
Halogen Bulb Kit
PartSelect #: PS12342510
Manufacturer #: WB49X29679
This light bulb is used in the interior oven. NOTE: This bulb has looped pins, not the straight pins.
No Longer Available
ELEMENT BROIL Assembly
PartSelect #: PS2370378
Manufacturer #: WB44T10099
If your oven isn’t broiling like it used to, this broil element might be the fix. It sits at the top of your oven and gives off strong, even heat to help brown and cook food from above. It’s perfect f...
$144.43
Special Order
GASKET OVN Door
PartSelect #: PS783572
Manufacturer #: WB32T10012
Struggling to keep the heat in your oven? Our GE Oven Door Gasket is here to help. It's more than just a spare part; it's your solution to creating a tight seal between your oven door and the oven ope...
$81.06
Special Order
Range Screw
PartSelect #: PS222157
Manufacturer #: WB01T10008
This part is a replacement screw for your oven. It is made of black metal and is sold individually. This screw is approximately 1/4 inch in diameter and about 1/2 inch in length. It is designed to con...
$13.95
Special Order
Wall Oven Rack
PartSelect #: PS1765903
Manufacturer #: WB48T10045
The wall oven rack provides a stable surface for cookware in the oven.
$99.08
Special Order
ELEMENT CONVX Assembly
PartSelect #: PS2321875
Manufacturer #: WB44T10086
This convection heating element is designed to provide steady, even heat during convection baking and roasting. Positioned around the rear fan, it helps distribute heat evenly throughout the oven for ...
$79.07
Special Order
Questions And Answers for JCKP70SM2SS
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the JCKP70SM2SS
[Viewing 7 of 7]Little to no heat when baking
Fixed by
these parts
these parts
Show All
Oven not heating evenly
Fixed by
these parts
these parts
Show All
Oven is too hot
Fixed by
these parts
these parts
Show All
Element will not heat
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Little to no heat when broiling
Fixed by
these parts
these parts
Show All
Touchpad does not respond
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Oven would go in to a F2 Error
Removed six 1/4" hex nuts on rear of oven. Then through front/inside removed a single 1/4" hex nut to actually remove sensor. Unplug sensor connector, remove. Reversed steps, push oven back in place and plugged in. Tested oven function.
Parts Used:
-
Peter from stamford, CT
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
148 of 226 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven wouldn't preheat above 300 degrees
Unplugged appliance and removed 5 screws on back of stove/oven and removed plate. Disconnected the sensor and unscrewed it on the inside of the oven. Pulled the cord through and replaced with new sensor. Replaced all parts and plugged in the appliance and tested. Worked great.
Parts Used:
-
Gerald from Cape Canaveral, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
54 of 94 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
I kept getting An F2 error and the temperature did not seem accurate
1) pull out the stove
2) remove the 7 sheet metal screws holding the back panel on. (the panel that also covers where the cord splits and connects to the oven.
3) Find the small plastic connector located in the middle of the back of the range and unplug it.
4) open the front of the oven and remove the one screw holding in the oven temp sensor.
5) replace the sensor and make sure to "feed" the new cord through as best you can.
6) I had to dig through the insulation a little bit to find the new wiring harness
7) connect the wiring harness and put the back of the range back on
note: this was very simple to do if you think this might be the problem don't hesitate to handle this one yourself.
2) remove the 7 sheet metal screws holding the back panel on. (the panel that also covers where the cord splits and connects to the oven.
3) Find the small plastic connector located in the middle of the back of the range and unplug it.
4) open the front of the oven and remove the one screw holding in the oven temp sensor.
5) replace the sensor and make sure to "feed" the new cord through as best you can.
6) I had to dig through the insulation a little bit to find the new wiring harness
7) connect the wiring harness and put the back of the range back on
note: this was very simple to do if you think this might be the problem don't hesitate to handle this one yourself.
Parts Used:
-
Chad from Bloomington, IN
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers, Socket set, Wrench (Adjustable), Wrench set
29 of 38 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!