JCB530SF1SS General Electric Range - Instructions

Unplugged the appliance for safety. Removed two 1/4" screws that held the assembly in place. Carefully removed the wire guard that retains the glass shield. Unscrewed old light bulb and replaced with new part. Reversed the steps after cleaning glass cover.

Took off oven door and removed racks. Removed the cover on the back side (5 screws removed with nut driver) Pulled sensor out the front side of the oven. Threaded the new sensor through and put all back together.

Originally the burner had a hole burnt through it, which resulted in a hole being burnt through the bottom of a pan. I replaced the burner and it would not heat up. I removed the top control panel, after securing power to the stove outlet, turned the power back on checked both sides of the swith with a meter (with the switch on) and had no power on one side. I went to two stores that did not have the switch in stock and ended up ordering from this site at about half the price! It arrived a couple of days later. I marked the wire colors on the old switch, took off the knob, removed two phillips head screws, pulled out the old switch and installed the new one and I was back in business. The hardest part was getting the sheet metal / heat gaurd positioned right upon re-assembly. To remove the panel there are two screws in the rear (nut driver) and a screw on either side of the front under each corner that require a torx driver to remove.

took of the back panel with a nut driver,pulled off the wires one at a time ,put them on the new switch in same position as the old switch.removed old switch with a screwdriver ,screwed in new switch,replaced back panel,put on switch knob

Removed the screws holding the back in place, then pulled off the control knob and removed the two screws holding the infinity switch. Swapped the leads from the old to the new switch and reinstalled everything. Worked like a champ!

Unplug stove first. Raised the stove top and propped up useing wooden spoon and wife assistance holding up. Pay attention to spot brackets hand to top. Removed sheet metal screws from bracket clamp holding burner in place. Removed one extension bracket from old burner and transfeered to new burner. Removeing one bracket clamp allows the other one to act like a hinge and make for easy removal and replacement. Back of burner had corresponding numbers which made it easy to replace brackets in same place as old. I carefully take one electrical wire at a time from old burner and transfeered to the new burner. Replaced burner same way it came off.

unplug stove first...take back of stove off to get to burner switch remove wires colors coded.. get new switch put wires on the same way.plug stove in test burner...very simple to replace.and save $$$$$$$$

I had to call for a appointment for repair with GE Appliance because I thought then it . .was something electrical. The technician came out & checked everything out, turned out it was not electrical, The technician went out to his truck got a light bulb from his truck, put it in & it worked. It cost me $121.00 for trip charge from GE appliance for a light bulb that worked, your light bulbs were defective twice. Very disappointed with your products, cost me alot of money for a good light bulb thru GE appliance

1) Turn off power at circuit breaker panel
2) Slide out Range from wall
3) Unplug Range
4) Remove back panel and unplug electrical connections to socket
5) From front of oven, remove glass cover over old oven light bulb and remove flange that holds socket and bulb
6) Remove old socket from mounting flange and discard.
7) Place new socket into mounting flange
8) Screw mounting flange and new socket into the oven from front. Reattach electrical connections from back.
9) Screw in new light bulb from front
10) Replace existing glass cover over new light bulb and snap wire holder in place
11) Replace back panel
11) Plug in range
12) Slide range back to original position
13) Turn on power
Works like a charm! Thanks for having the parts after 30 years!

took off cover, pulled all wires off switch, pushed wires on new switch, put cover back on. Whalaa..

Removed the screw from the broken piece and put the new piece on and put the screw on.

Red Light Off

I turned the power off at the circuit breaker, pulled the stove out from the wall, and removed the plug. I removed the top back panel, and took the burner switch out by unscrewing the 2 screws in the front of the panel. I used pliers to remove the wires one at a time from the bad switch and put them on the good switch. I replaced the new burner switch on the front panel and also, replaced the back panel. I put the plug back in the socket, pushed the stove against the wall, and turned the power on at the circuit breaker.

Went to You Tube, found the appropriate segment. "Wa La" the problem was solved. Burner is working the way it is supposed to.

First replaced the 8" burner element-still did not work.
second: replaced the TERMINAL BLOCK KIT still did not work.
third : finally replaced switch: very easly-make sure you do not take off any of the wires on the back of the switch-take new switch and replace each wire on the same location than remove the old switch and replaced wired new on with the two screws.