JCB2388ARA Jenn-Air Refrigerator - Instructions

removed the cover from the back of the refrigerator, and used the nutdriver to loosen screw on the single outlet water valve, removed the old water valve and the hoses to it. Connected the hoses to the new valve and attached to the wall of the refrigerator by tightening the screw. Then removed the old ice maker from the inside of the refrigerator, by loosening the two screws and attached the new one, I tightened the screws and then I was done. It is working great.

Replacing the icemaker is pretty simple. Three screws, an electrical connector. Hardest part is getting to the icemaker since the freezer is below the refrigerator.

Removed the old icemaker and installed the new one. The first one we ordered lasted about 4 weeks and pooped out. Parts Select was very nice and gracefully sent another in two days time. This one has been installed and is working fine...Hope it stays that way.

Thanks...Ron Norwood

This was a very easy repair. Of course start by unplugging the power cord. Take out the lower freezer drawer. Unplug the wiring harness from the ice maker at the rear of the freezer. Undo 3 screws with a 1/4" nut driver. The ice maker will come right out. You don't have to undo any water connections, the feed tube just slides into a guide in the ice maker. Once the ice maker is out, unplug the harness from the old one and snap it into the new one. Same with the cover. Reassemble in reserse order. Plug the power cord back in and wait a couple of hours for the familiar sounds of ice cubes falling into the tray.

Replaced ice ice maker using
All of the instructions on the website.
Very easy. A couple of the screws I had
To feel for because I couldn't gety big head
In the freezer far enough to see them.
Very simple and only took about 15 minutes.

Release tabs at right and left rear of cover and pull cover forward. Remove all hex-head screws. Release housing assym from screws in middle of assym. Defrost assym is at the back right. Unplug wire connector. Plug in new defrost assym, and set into place. Hook housing assym back onto screws. Replace all hex screws. Slide cover back into place. Done!

I removed the top refrigerator side hinge screws. The door came right off. Slipped in the lower hinge pin.. Unscrewed the natural door closer and replaced. Reinstalled the door. It is unfortunate that these parts are plastic. They wear out way too soon. No, the door is not over weighted. If you have no weight in the door the plastic shelves will hinder the door closing. Putting stuff on the shelves makes them take their proper form.

After taking advice from the other posts, I removed all contents from the door, removed the screws from the top hinge and then lifted the door off the bottom hinge pin.

While door was lying flat I unscrewed the old natural closer, replaced it with the new one. Swapped out the old lower hinge pin with the new one.

I then had someone help me lift the door back on the hinge pin and fastened the top hinge screws while they held the door in place.

It worked perfectly and was very easy.

Replaced ice maker but now water valve wont work

I read the previous repair story and agree with the author that the screw behind the front piece was difficult to remove and re-install. If I had a magnetized nut driver I think it would have been easier. There were no installation instructions so I relied upon the repair experiences. The other two screws came out easily and I found the harness release easily and the harness was easy to reinstall.
I am not a good handyman but was able to install the new ice maker

At first I thought I had ordered the wrong bracket but all I had to do was push it up and pull down and it snapped right in place. If a 71 year old lady can do this any body can do it. Thank you for the fast service.

Had a little trouble getting the plastic cover removed. Trick is to reach all the way to the back, put finger in hole behind the tab, and pull down and forward so it clears the little plastic locking nub behind the tab on the right.

to easy to describe, remove 3 screws and a wire plug then install new unite.
Works great
Thanks

Took under 5 minutes. Removed two screws and unplugged the wire bundle from refrigerator. Removed old unit. Put old wire bundle on new unit. Plugged wire bundle back into refrigerator and remounted the new ice maker. Could not have been easier. Watched the video first, it was very helpful.

Unplug wire harness back of fridge. Unscrewed 4 screws on guide for ice bin. then unscrewed two screws holding ice maker to wall of fridge. removed ice maker. then had to take front cover off (pull hard, it comes off) and remove wire harness plug from the ice maker. save this, front cover, and all hardware to re-use. reverse steps to reinstall, including wire guide that goes up and down to stop and start ice maker when bin fills. Have to put this into front part of ice maker correctly for it to work. make sure it is down so that it will produce ice. ice tray took a few hours to fill with water initially, must be on a timer or something.