JBV42G201 General Electric Range - Instructions

Pulled out the old burner that was held in by a metal spring clamp. Pushed the new one in.

Good as new.

We just remove the old surface unit and insert the new one by hand. Thanks to PartSelect, we were able to buy really good quality part that works right away! It was a 26-year-OLD GE Stove/Microwave space maker, the parts were hard to find in stores. Thank you for selling this! All the best for your business!

The only hard part of the job is removing the old, corroded terminal block. Be careful not to break the electrical wire. Other than that, just sand the contacts and reassemble. This is the second one I have replace on my 4 burner stove. 2 more to go.

I located and removed 2 sets of hex-head screws under the front lip of the cooktop, then lifted the entire cooktop to access the burner controls. Removed the wires and taped them, and took out the old control after removing 2 phillips head screws. Installed replacement part easily. Only tricky part is that the various shaft adapters don't quite work with my knob. I'll fix it completely with a bit of epoxy and the adapters they sent.

Replaced old drip bowls with the new ones. Very simple, no tools required.

1. Went on line to your website.
2. Ordered the parts
3. Rec'd your package.
4. Installed ("plugged in") the new parts.
5. Voila !

it was hard to figure out the instructions from A switch to B switch to my switch. The first switch was no good the second one was good. prayer book didn't hurt.thank

I have had to replace this unit once before. It was very obvious which terminal had burned off. Removed the total front panel. Removed the timer and replaced wires from one unit to the other. Also had to strip off one wire connection and replaced it .

I flipped breaker off for electic and confirmed that power to the stove was off. I removed the 2 screws holding the control unit in place. Carefully removed all knobs and buttons and pryed the cover for the control unit off. I then removed old part, removed the wired and clipped wires to the new unit. Put cover back on - has some difficulty getting the panel back in place to line up the screws. But after a couple of attempts, was able to line up unit and put screws in place to secure. Replaced all knobs. Turn breaker back on and cooked lunch. Very easy job. Most difficult part was getting panel back in position. I would watch alignment more carefully before I removed in next time. Easy home repair for Women...not sure about my man?

1) Took photo of original wiring behind original clock. 2) Marked up wiring instructions for new clock with wire colors. 3) Marked wire colors next to posts on new clock. 4) Removed old clock and its metal mounting bracket. 5) Installed new clock onto old mounting bracket.PROBLEM: The holes in the glass facade of oven are shifted about 1/4" off from the pushbuttons on the new clock. 6) Remove bracket and enlarged holes by 1/4" sideways. This includes shifting the holes for the oven light pushbutton switches, and the four "racetrack" holes where the bracket attaches to the oven. Plug wires into new clock, using extender wires provided as needed. Labelled extender wires with their "colors". POWER UP. The clock works, and the "Timed Bake" works. However, the Self-Cleaning of the oven cannot be started, because the latch level cannot be moved to the right (locked ) position. This leaves us unsatisfied, as restoration of Self-Cleaning was the reason we decided to replace the oven clock.

Just plugged it in! Very easy.

Plugged it in. It fit!

Good directions

The original controls were different for the small burners and the large burners. The replacement part fits all. Before removing wires, pay attention to writing on new and old control and replace 1 at a time. The hardest part was being sure to cut the knob stem to the correct length. Control works well.

Remove light bail, glass cover held by two nut screws. Pull socket, removed clips in back, replaced wire connectors, placed new socket in, then glass cover and bail. Wire connected in back, cover plate replaced.