All Installation Instructions for General Electric Range JBP15CJC

The light inside the oven had burned out

0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.

Parts Used:

Light Bulb - 40W

Catherine from SEATTLE, WA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

3 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Bottom part of the Drawer Glider broke off on both sides of the drawer.

Remove the draw from the stove. Then unscrew two Phillips Head screws ( one on each side). Remove the old gliders. Slip in the new gliders. Screw the two phillis head screws back in. Make sure when you put the drawer back in the stove that you lift the front of the drawer up enough that the lower portion of the new glider is engaged on the side rail of the oven drawer space.

Parts Used:

Drawer Glider

William from SPOKANE, WA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

It was burned out

I just follow Steve's Installation Vidio. My range works.
Thanks Steve

Parts Used:

Surface Burner Terminal Block Kit

lan from SANTA CLARA, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Needed new drip pans

Replaced drip pans

Parts Used:

Drip Bowl - 8 Inch

Drip Bowl - 6 Inch

Patricia from GORDONVILLE, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Neither set of cooking/broiling coils worked

This cooking element has four electrical connections to the stove.
YouTube videos show connecting the coils from inside the oven.
That does not work.
One of the electrical connection is made too short to pull through the back of the stove; as shown in the videos.
Be SURE to Trip the circuit breaker to the stove before starting..
The "easy" way is to pull the stove from the wall and open up the back panels. Then disconnect all 4 electrical connectors from the bad element. Unbolt and disconnect the old element from the stove.
Install and bolt on the new elements. Attach the electrical connectors in the back. Reset the circuit breaker and test the coils to see they light up. If OK, trip the circuit breaker and reinstall the back panels.
Push the stove back to wall and energize the circuit breaker.

Parts Used:

DOUBLE BROIL

Albert from READING, MA
Difficulty Level:
Difficult
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Pliers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Terminal block connectors worn out wasn’t making a good connection with the stove top burner

Cut 4 inch’s off the new terminal block wires then using my wire strippers stripped 1/2 inch off the ends , the old terminal block wires I stripped 1/2 inch at the ends using a wire nuts on both wires and electrical tape connected the terminal block to the stove plugged the new burner in and the burner worked 100%.

Parts Used:

Surface Burner Terminal Block Kit

Lance from HAHIRA, GA
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

gasket door replace

the instructions given for this part were not 100 % accurate, our oven door required multiple, dis assembly and was unable to complete the task, local handy men refused to come to assist since the job was already started, it appears I will now need to buy a new oven , I was disapointed in the help because had we known we had the more diffcilult oven, would not have attempted, I did give the correct model and serial number to the person when discussing this part

Parts Used:

Door Gasket

David from HIGHLAND PARK, IL
Difficulty Level:
Very Difficult
Total Repair Time:
More than 2 hours
Tools:
Nutdriver

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

lights blown out

replaced lights in refrigirator and freezer

Parts Used:

Light Bulb - 40W

Gerald from WINTERVILLE, GA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

6 of 14 people found this instruction helpful.

Was this instruction helpful to you?

I'm Very Very Happy Was My First Order From This Part's Company ;

100% Pleased I Got & Installed All In A Few Minutes Your Company Is The Best Thank You Very Very Much ; Antonio

Parts Used:

Drip Bowl - 8 Inch

Drip Bowl - 6 Inch

SURFACE HEATING ELEMENT

Surface Burner Element - 8 Inch

ANTONIO from E STROUDSBURG, PA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

oven racks very old and writing on knobs worn ff

Very was ti replace racks and knobs. Very fast mail service

Parts Used:

Oven Rack

Patricia from SAN JOSE, CA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Old Burner Chrome Ruined

Replaced

Parts Used:

Drip Bowl - 8 Inch

Drip Bowl - 6 Inch

RALPH from TROY, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

3 of 6 people found this instruction helpful.

Was this instruction helpful to you?

lens snapped off on the inside-plug was left loose

popped out the remainder of old lens, then pushed in new ones and slipped on plugs.

Parts Used:

Lens

RICKEY from MONTROSE, NY
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

3 of 6 people found this instruction helpful.

Was this instruction helpful to you?

The lower,BAKE, element had burned in half almost causing a fire.

Slide the rang out to access the 240V plug & unplugging it. Removed the sheetmetal cover from the rear of the range to access the slip on wire plugs to prevent damaging the insulation. The insulation would be damaged if pulling them through the opening in the oven wall with the plugs attached to the element. Removed the racks from the oven. Unscrewed the retaining screws holding the element to the rear wall of the oven, lifted damaged element out and reversed the process for instillation. Perfect opportunity to clean underneath and behind the range.

Parts Used: