JB900SK6SS General Electric Range - Instructions

First I searched for the part here and I had a slightly hard time finding the correct element on the site.
Then I read the comments of the others and the issues they faced.
I unplugged the range and pulled it out a bit from the wall. I then removed the two screws that hold the element in place and put them where I would not lose them. Then I gently maneuved the element out and placed a clothespin on each of the wires to keep them from going back in and then disconnected the wires from the element using a pair of needlenose pliers.

At this point I had to gently bend the new element back into shape as it had been bent during shipping. Then I connected the wires and slid the element into place and installed the two screws.

Double checked to make sure everything was ok plugged in the range, said a quick prayer and set the temperature to 300. When it got to 300 the element shut off and I was happy that the element did not take any other parts with it.

Removed screws holding temp sensor, pulled wire out from behind wall until found connector, disconnected old sensor.
Measured resistance of old sensor and compared with new sensor, they measured nearly the same. Installed the new sensor and tested the stove. Came up to temp ok. No problem since, about 2 weeks.

My stove didn't seem to be getting enough power for the oven to heat up and the burners to get hot enough. When I checked the connection of the electric cord I found that one of the 3 terminals that the plug connects to was broken off. When the new part came I removed the old part by first disconnecting the 3 wires [black,white(ground),red] and then using a small but long 1/4 socket (that I found at Lowes)I removed the 2 screws that held the old part to the stove and the green screw under it holding the flat copper piece that also connects under the white ground wire of the part. I mounted the new piece on with the 2 1/4 screws. The new part comes with a piece of copper that is for grounding the part to the stove. When I compared it to the old part it was a little different. I first screwed the copper piece onto the stove (under the part) with the green screw then I screwed the white wire over the copper piece to the center terminal(you have to make the hole of the copper piece line up to the screw hole). I connected the other 2 wires and then connected the electric cord to the new terminal block and then put the back cover back on the stove and plugged it in. The clock came on I turned on the four burners they all got hot and red. I turned on the oven the element on the bottom got red I then turned on the broiler the top element got red. My stove is fixed.

0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.

Pull oven out away from the wall, unplugged from outlet, removed center cover by removing 5 sheet metal screws. disconnected thermostat sensor from control cable. Opened oven door and removed screw that holds thermostat sensor. Pulled thermostat sensor out replaced with new sensor. Plugged sensor in to control cable. Replace panel and screws. Then my wife made me clean the oven. I recommend making the repair when your wife is not home.

replaced lights in refrigirator and freezer

Would have helped it I knew the push on terminals of the bake element were visible and accessible to slide the terminals on from the back side of the stove in the beginning. There is not enough slack in the the terminal wires to connect them from the oven side, so you will have to open the back panel to retrieve a wire anyway. SO, CONNECT THE BAKE ELEMENT TO THE OVEN WALL FIRST ! Then, open the back panel of the stove and simply slide the terminals on the exposed slide terminals of the bake element.

Not only did we (my wife did help) replace the dual element but afterwards we realized the control switch was not functioning properly and so that was replaced as well, and now our appliance works as intended. Also the instructions, are helpful as well. We used care not to force or over tighten anything and with two sets of eyes and the extra hands everything went much better. Anything that was removed was noted as to it's location and replaced .

it went well as compared to getting a new ~~800$ cooktop and ~~150 to install, I took a shot for 30$ bucks and it worked great!! problem solved and great support ! !! thanks for all your help

I thought it was the burner thermostat, so I replaced the burner unit. By coincidence, the ceramic outer portion of the burner was cracked in two places, but otherwise intact. That was not the problem, though since the new burner did the same thing as the old one. Then I new it was the Infinite Control Switch, so I ordered it. Replacing it was easy. I turned off the cooktop circuit breaker and made sure no power was going to it. It is powered by 240 volts so you need to be very careful to turn off the power before doing any servicing on it. I then carefully pried up the glass cooktop and lifted it out, so it wouldn't break. By taking off the control knobs, and removing several small Phillips head screws all around the metal cooktop frame and just under the edge of the glass cooktop, I could lift the glass top off from the cooktop, and place it on some newspaper so it didn't get broken. It is important to keep the rest of the cooktop upright. The burners are not fastened down, and only gravity holds them in place. They normally sit on two springloaded pins, one on each side, and the weight of the glasstop pushes them down to their proper setting. So don't mess with them, and make sure each side remains on the two pins after you're done and before putting the glasstop back on. As for the switch, you need to remove two small 1/4 inch metal screws (a socket is very handy for this), one on each side of a metal framework that holds all the switches. After removing that framework, I carefully turned it over and found the correct switch for the burner that wasn't working. In my case, it was the closest right hand burner, which is also the biggest and has the option of having a big, small or both elements turned on, depending on how you turn the control switch. I then carefully pulled off each wire lead, with a needlenose plier to avoid damaging them, and immediately put each wire onto the corresponding same connection on the new switch. Take a close look at the wires on the old switch to make sure you plug them into the same connectors on the new switch. It's pretty straightforward. There may have been one or two small screws holding the switch onto the framework, but I don't recall right now. It was very easy to see how to remove and then reattach it. Then reverse the above steps and reinstall the cooktop, turn on the power and you should be in business!

Gizmo = Bake Element held in place with 2 bolts inside of oven. Removing them only difficult because they are so deep in oven. I did not have the correct size nut driver so I started with my socket wrench then switched to putting the correct size socket on the end of a long screwdriver. After removing the 2 bolts fund element did not slide out easily so went to back of stove and removed a metal protective cover. Found electrical lines secured to the ends of the element. Had someone hold element while I pulled each of the 2 loose - at which time bake element fell loose. Put new one in by reversing the process. That night wife set stove to Clean - and said best it has been cleaned in years.

Ordered the bake element part from partselect.com. When the part arrived I removed the 2 6mm screws from the element, I used two clips to hold the wires in place so that they didn't receed back into the stove. I installed the bake element, installed the two scews ans was done. It took all of 10minutes.

Lily in Florida

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. ordered the part and connected the element back to the two wires replaced the two screws plugged in the stove turned on the oven and we were back in business,

First, pulled out the old heating element and all the peices that were left after it fell apart. Since when you pull out the old one, the wires it connects to tend to recess back into the oven wall, I had to pull out the oven and take the back cover off in order to push the wires and connectors back through the receptacle in the oven. This was really easy as you only have to remove 5 screws from the middle panel on the back of the oven rather than the entire oven back. Once the wires were back through, I just plugged in the new unit. The oven works just like new now. I'm sure I was able to save between $75 to $100 just for the service call by doing this myself.

Removed power plug- disconnected wire, removed cover over wires two screws, and removed old heated strip, held in by two screws inside of oven
Slide in new coil installed two screws, connected two wires replaced guard over wires, plugged in stove, cooked a rubarb pie, success