JB900BKB General Electric Range - Instructions

Pulled the oven out of it's location. Disconnected the power cord from the Electrical Outlet. Removed the Protective back plate (from the rear of the oven) which covers the wiring. Disconnected the two leads that connect the Baking Element. Went to the front of the Oven, opened the oven door, removed the two screws with a socket wrench (you can use a screw driver as well), at this point you can replace the element with the new one and secure with the two screws. I then went back to the rear of the oven and reconnected the two wires back onto the new heating element and replaced the wiring protective back plate. Reconnected the power cord to the electrical outlet and turned on the oven to see if the element heats up. AND IT DID. Moved oven back into it's original location and I was done. This took 16 minutes to do and saved me a nice amount of money. I could have had a service person show up and do this work which would have cost me $189.00 (Parts & Labor) to have done and all I spent , by ordering the part from PARTSELECT.COM, was just under $50.00.

The first step was to determine whether the problem was with the fan itself or the switch. I did this by opening the back cover and using a Volt meter to verify that the fan was not getting power. (I could have skipped this step.)

Next, I unplugged the range, closed up the back cover and lifted the range hood by removing two hex head screws that are just inside and on either side of the top of the opening in the range door. Propping the hood open, I removed the connector leading to the switch, then pushed the switch out the front. Inspection showed that the switch was damaged so I closed up the range and ordered the part from Part Select. Once the part arrived, it was a 15 minute job to unplug the range, lift the top, install the new switch, and close up the unit.

Caution. On starting to install the switch, I failed to unplug the range and my finger brushed one of the hot contacts leading to the switch. Thankfully, I was not injured. Do not repeat my mistake on this issue. Unplug the range even if you're only installing this simple switch.

I (1) pulled the oven away from the wall to get the back of it exposed. Then I (2) pulled the plug out to make sure there was no electrical current. Then I (3) opened the oven door and tugged on the broken heating element to see how tightly it was connected in the back of the oven. Next I (4) went to the back again and slid the silver-colored metal cover that protected the exposed electrical wiring for the oven. I (5) observed that there were a number of different colored wires held in place by screws as well as some wires that disappeared into the insulation, so I (6) went back to the front of the oven and pushed the broken heating element backward to determine if its wiring would become visible from the back of the stove. I (7) observed from teh back that it did. From that point, I (8) pulled the heating element's wiring connections through the insulation until it was visible. The I (9) unscrewed the two nuts connecting the heating element to the oven's wiring. Then I (10) went back to the front and pulled the broken heating element out and (11)inserted the new heating element. Then I (12) returned to the back and connected the loose wires to the heating element and (13) pushed the heating element forward into the oven. I (14) went around to the front to ensure the heating element was positioned the same way in the oven as the old one was, then in the back (15) replaced the metal shield over the wiring and isulation, (16) plugged the oven back in and (17) turned the oven baking setting on to a high temperature to test the new element (i.e., that it was connected correctly and actually worked). I (18) observed that the oven began heating up quickly to the proper temperature, and I was greateful the new bake element worked as good the original part. I then (19) turned the oven off and pushed it all the way back to its place against the wall.

The repair job was not effortless (about 15-20 minutes) but was simple enough NOT to require an electrician. The most difficult part was physically sliding the stove out and back into its tight place between our counters.

First and foremost, I am a 63 year old cooky baking GRANDMOTHER. I don't know anything about fixing appliances. I read the other repair stories pertaining to my burner and I thought, "why not."
It was a snap!

My part arrived the very next day, bless you Parts Select! I just did what the others (see above) did: I removed 2 screws to release the stove top, then I took a few digital photos to be sure I would know where the wires went. I released the old burner, pulled out the thingamajigs that held the wires in the old burner, then pushed the new ones in their place, replaced the stove top, plugged it back in, turned it on and jumped for joy! If I can do this, anyone can.

Ordered window pack from PartSelect then removed oven door from front of stove, then removed back of door and silver backing and glass pack. Dropped new glass into place. Replaced all backing,put door back onto stove. Tip. When removing screw keep them separated from each other as not to get mixed up when putting everything together. Good Luck, PartSelect has all the parts you need, this my second getting a part from them.

The burner would work but you could not regulate the heat. I ordered and replaced the control switch for that burner. The part was like for like and reasonably priced compared to other websites and dealer. The picture showed that it was identical. I ordered one day and it was here the next. I had drawn a diagram of where the wires went on the old switch so it was very easy to replace. Probably took me 15 minutes or so. Works perfectly and by buying from this website it saved me a few bucks.

Unplugged the appliance for safety. Removed two 1/4" screws that held the assembly in place. Carefully removed the wire guard that retains the glass shield. Unscrewed old light bulb and replaced with new part. Reversed the steps after cleaning glass cover.

I am a 69 year old woman. I watched the Repair Clinic YouTube Video before I started. I then pulled stove away from wall and unplugged it. Took off oven door and removed the top oven rack. Loosened and removed the screw holding the temperature sensor located inside at the top center back wall of the oven. Pulled the sensor through the opening until the plastic plug came through. Unplugged and removed it and plugged in the new sensor. Fished it back through the opening. Replaced the bracket to the back wall of the oven and tightened the screw. Replaced the oven rack and stove door. Plugged it back in and moved it back into place. I turned on the oven and let is heat for over 30 minutes and the internal temperature was correct with the setting.

I order the part online on the 23rd of February 09 in the afternoon it was delivered on the 24th to the address in Florida and then fedex to me in Cayman. So I got it on the 2nd of March went home that evening after work got my pliers unpluged the stove removed the two screws that holds the element in place. I also removed the metal from the back of the unit first to make sure I was doing it right. I then pulled the element at the back and disconnected the two wires replacing it with the new one. I then replaced the back and screws and pluged it in turned on the oven waited and when I saw it turn red I felt so good. I said thank you Lord and then baked a cake. The whole installation took about 20 mins.
Thanks again.
P.S. please look into offering shipping orders overseas.

Shut off circuit breaker. Removed cooktop from island counter. Removed all knobs. Removed all screws after finding layout diagrams of unit on your web site. Lifted glass top from metal cabinet. Ordered control after trouble shooting the problem. (Master Electrician). Obviously burned out from water in control. Ordered control on line and installed it when it arrived three days later. Before installing control I cleaned and dried out the area. I cleaned the glass top around all the control shaft holes and the rubber boots and lubricated them with silicone to help keep them dry and for ease of turning controls. Turned on circuit breaker and checked all burners, pilot light and hot top indicating lights.

The hardest part was getting the correct part. I trusted the on line number and the first part I received was incorrect. I should have taken the part number off the old switch. When I did, I found out that the part number changed when I tried to order it. When the part came, the wiring instructions were not even close. I just took one wire at a time off the old switch and put it on the same terminal of the new switch. The repair was/is very simple made complex and too much time because of a wrong part and incorrect wiring instructions. As far as getting the incorrect and correct parts through the mail it was very fast. Received both parts in less than 3 days. A bonus is that I sent the old switch back for a rebate. Thanks for that.

With circuit breaker off, I opened the oven door and removed the two mounting hex-head screws that held the cooking element at the rear of the oven. I pulled the oven away from the wall and unplugged the unit's 220 volt power cord from the wall. I removed the rear cover panel by removing five hex-head screws that held the panel in place. I sought out the wires that connected to the oven element and pulled the tabs from the failed element. I moved to the front of the stove to remove the old element. As the contact ends of the element are curved up, I needed to lift the front of the old element up to an approximate angle of 45 degrees before I was able to remove it from the oven. I then placed the new element into the mounting holes, again with the front of the element raised at an angle. Its insertion was easily performed. I replaced the main element mounting screws at the rear of the oven. I went to the rear of stove again and reconnected the power tabs to the element contacts. I repositioned the rear cover panel and replaced the five hex-head screws to secure it into place. The main power was reconnected to the power outlet and carefully slid the stove back into position. Circuit power was reset and the oven tested successfully.

My oven bake element melted one day. I had my husband replace it and for a short while it worked. Then it quit but then our broil element would not shut off. My husband said that it might be the heat sensor. We checked here in town and that element cost over $80. Since we have order from Parts Select before we decide to do so again. When we received the heat sensor my husband replaced it taking out the original heat sensor. This did not work as the broil element still would not turn off. I call the repair man and I found out that the initial melt down of the bake element also effected the main circut board that had to e replaced.

First turned off power at breaker box. Pulled stove out to remove the half dozen hex screws on the back panel.(some nuts were stripped)Removed old oven sensor inside oven held by one hex screw and replaced it with the new part. Oven works great now! Repair job was done by husband Mike.

Disconnect power, then remove racks from oven, locate heat sensor by the broiler element. Use ratchet with extension and correct socket to remove the bolt directly under the heat sensor, pull the sensor out till you see the plug, disconnect the plug and then connect new sensor to it push wire back thru and then rebolt the new sensor on, thats it...