All Installation Instructions for General Electric Range JB750SF2SS

burner was inoperative

verified switch operation , checked continuity of burner element found open ordered new part and installed next day
after extremely fast
service from partselect thank you

Parts Used:

Range Surface Element Control Switch - 6 Inch - 1560 W

bryan from cocoa, FL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Screw drivers

0 of 2 people found this instruction helpful.

Was this instruction helpful to you?

The oven temperature could not be controlled

Disconnect the range from the mains. Open the door. Remove the single screw holding the temperature sensor - this is located on the back wall on center and is screwed to the broiler mounting plate. Remove the four screws holding the boiler element and allow it to hang down on the wire; this exposes a space to feed the wire through later. Now move to the back of the range and remove the six screws that hold the central cover plate. Now push the insulation to up out of the way and you can disconnect the temperature sensor, pull it out through front, insert the new one and connect it. Reassemble in the reverse order. Mine worked perfectly!

Parts Used:

Temperature Sensor

Keith from Annapolis, MD
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Socket set

Was this instruction helpful to you?

Replacment of burner control switches

I watched your video on the subject and followed it exactly. It explained everything I needed to know. The hardest part was CLEANING under the stove once I pulled it out from the wall!

Parts Used:

Range Surface Element Control Switch - 6 Inch - 1560 W

Judith from Keezletown, VA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Screw drivers

Was this instruction helpful to you?

rear drawer supports broke

Directtions were by diagram only, no written instructions. Drawing was small and difficult to follow but the repair itself was easy.

Parts Used:

REAR SUPPORT

TERRY from RICHMOND, VA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set

Was this instruction helpful to you?

f-2 or f-3

remove two bolts in on sensor and slip thru back un plug and reverse to put in

Parts Used:

Temperature Sensor

daniel from gap, PA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers

Was this instruction helpful to you?

F2 reading

Followed the instructions that were sent to me by E-Mail.

Parts Used:

Temperature Sensor

lynn from sunnyside, NY
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers

Was this instruction helpful to you?

Stove drawer rear guides broken

Installed new guides with a nut driver without any problems.

Parts Used:

REAR SUPPORT

Robert from Shakopee, MN
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

Was this instruction helpful to you?

Range lower drawer would not stay on track.

Easy to install replacement parts using the screws provided.

Parts Used:

REAR SUPPORT

Richard from Newark, DE
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

Was this instruction helpful to you?

Broken drawer support

Followed the example picture on the part bag. Anyone could do this, incredibly easy. Took about 4 minutes to install both sides.

Parts Used:

REAR SUPPORT

Mario from Deer Park, WA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

Was this instruction helpful to you?

Convection fan came loose from shaft

Convection fan came loose from the shaft with a lout rattle and grinding as the fan spun down. Had to remove four metal screws to remove the fan cover. Initially tried to just put the nut back on to hold the fan. However, I could not get the nut to start, so I assumed that threads were stripped on the nut or the shaft. Ordered the replacement nut, hoping that it was the nut that was the problem. However, I had the same problem with the new nut. I could see no damage on the shaft. It finally occurred to me that the nut and shaft had left-hand threads (counter-clockwise to tighten). At that point, it was extremely easy to put the nut back on and tighten it. I did not try using the old nut, since I had already received the new one, but I'm certain that if I had come to that realization earlier, I could have saved time and money. So, if you have the same problem, try putting the nut on "backwards."

Parts Used:

NUT

Thomas from Albuquerque, NM
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set

Was this instruction helpful to you?

Flashing F2 and erratic temperature readings.

Unplugged from wall outlet, then opened oven front door. Reached in and removed two screws. Pulled oven sensor threw and detached electrical connector from old sensor. Plugged in new oven sensor and reversed removal procedure. No more Flashing F2 and oven temperature came to ready. Very easy.

Parts Used:

Temperature Sensor

Kenneth from Salem, OR
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

Was this instruction helpful to you?

Our bottom drawer support broke and the bottom drawer was canted

Simply removed drawer and lined up the newsupports. Made sure the guide pin was lined up and installed with single screw

Parts Used:

REAR SUPPORT

Robert from Woodinville, WA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Burner Would Not Turn Off

Replace control switch

Parts Used:

Range Surface Element Control Switch - 6 Inch - 1560 W

BILLY from WEBSTER, FL
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver

Was this instruction helpful to you?

Pilot light out

Removed the power plug from the wall, screwdriver and small socket allowed me to remove the front control panel. Once I located the pilot light I pulled off the holding clips and placed a new light into the holding clips...problem solved.

Parts Used: