All Installation Instructions for General Electric Range JB690DF4BB

oven door gasket needed replaced

Ordered the part, it arrived and 5 minutes later it a complete installation

Parts Used:

Range Oven Door Gasket

Mary from LONGS, SC
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

THE FACE PLATE IS HARD TO GET OFF THE OLD CONTROL BOARD. USE A THIN KNIFE

THE INSTRUCTIONS THAT COME IN THE EMAIL ARE VERY GOOD. BE SURE TO TAKE A PICTURE OF THE WIRING.

Parts Used:

CONTROL OVEN TO9

Melvin from WEBSTER, TX
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers

1 person found this instruction helpful.

Was this instruction helpful to you?

Not Reaching Temperature above 300 Degrees

Take off 6 screws of back cover of the range, unplug the white wire. Go to the inside of oven, pull out racks. At the top of the oven is your Broiler element, in the center you will see a rod sticking out with one screw holding it in place. Take out screw and pull temperature sensor out toward you. Reverse steps to put it back together.

Parts Used:

Temperature Sensor

Ron from SAN TAN VLY, AZ
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

1 person found this instruction helpful.

Was this instruction helpful to you?

Oven board went out

One wire at at time then used my razor blade to get front off stuck right back on

Parts Used:

CONTROL OVEN TO9

Jackie from TICKFAW, LA
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers

1 person found this instruction helpful.

Was this instruction helpful to you?

Plastic guide Broken

replaced Plastic Guides

Parts Used:

Bottom Drawer Guide

NICK from Vernon, CA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

9 of 25 people found this instruction helpful.

Was this instruction helpful to you?

Element blew hole in self then no power to burner.

Replaced burned element, did not fix no power problem. Ordered receptor replacement, replaced it, took less than 10 mminutes, but still no power to burned. Then ordered replacement switch, replacement too less than 10 minutes again and burner works fine.

Parts Used:

Range Surface Element Control Switch - 6 Inch - 1560 W

Melvin from Portland, TN
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers, Socket set

2 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Latch n handle to seal the oven during the self cleaning oven wore out and once engaged would not release

Remove the old oven latch and replaced it with the new replacement part. It was very easy to remove and replace with just a few nuts removed

Parts Used:

Black Latch & Handle

Daniel from HAHIRA, GA
Difficulty Level:
Very Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set

1 person found this instruction helpful.

Was this instruction helpful to you?

Oven door wouldn't close properly

Watched video on you tube. Removing/reinstalling all of the screws/bolts took longer than the actual repair.. Took 23 minutes total from turning power off, repairing and turning back on. Super easy!

Parts Used:

Black Latch & Handle

Lynn from N CHESTERFLD, VA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

The storage drawer came without supports.

I just removed the drawer and installed the rear supports as instructed on paper included with the part.

Parts Used:

REAR SUPPORT

Dock from Aurora, CO
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

2 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Outside portion of Element broken

First unplug range from electrical outlet!
Removed screws under front edge of stove top, propped it open with long paint stick, pried clips off of the element, unplugged and plugged in new element, push element back into clips, closed top on stove, plug back into socket, tested new burner, put screws back in under top front edge of stove top!!!

Parts Used:

Haliant Element - 12 Inch

Tiffany from Lexington, OH
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers, Socket set

1 person found this instruction helpful.

Was this instruction helpful to you?

Handle would not pull the latch back any longer

Super easy repair! There are videos online if you have one type of oven, I had the other type (with the little silver plate right above the latch part). The trick is to remove the handle from the assembly itself before removing or placing it in the oven. 4 screws total and I recommend needle nose pliers to help remove the wires.

Parts Used:

Black Latch & Handle

Caitlin from MOUNT SHASTA, CA
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Oven no longer working after running the self clean option. Only Stove top burners worked

I began by turning off the breaker in the panel.
Slide the oven out into the open area.
Removed 3 screws in order to remove rear top panel.
Took 2 pictures of the wiring location on the PCB
Removed all wiring going to the circuit board total of 8.
Removed 4 screws in order to remove bad PCB.
Remove faceplate from bad PCB (you will need to place this faceplate on the new PCB.

To Install.
Reverse steps above

Parts Used:

CONTROL OVEN TO9

Dominick from THORNWOOD, NY
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Bake button stopped registering

This was simple enough to repair for me, a relative novice. Just remember you need a nut driver to take the back panel off, take a photo of the existing board so you remember which wires go where, and you definitely need a hair dryer to heat up the sticker on the old board so you can remove it and put it on the new board.

Parts Used:

CONTROL OVEN TO9

Ryan from COHOES, NY
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers

1 person found this instruction helpful.

Was this instruction helpful to you?

Hole in gasket

I took the oven door off. Laid it down on a blanket on the floor. I pulled up on end going into the door, then went around with fingers to feel where the clip were and grab the clip with my fingers and gently pulled up. Then grabbed the new gasket, found the center clip that goes at top of door and started pushing the clips in. The last was feeding the ends back into the slot in the door.

Parts Used:

Range Oven Door Gasket