All Installation Instructions for General Electric Range JB655DT1BB

dead mice in insulation, chewed wire on latch switch

replaced insulation

Parts Used:

Don from Flagstaff, AZ
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Pliers, Wrench set

Was this instruction helpful to you?

Thank you for voting!

one leg of the terminal block was loose and overheated under load.the terminal block melted and could have caused a fire.

I took a picture of the setup and damage . I then disconnected the burnt wires and replaced the wires . Then I installed the new terminal block and connected the wires to the proper positions. The reason for the failure was that the delivery people didn't tighten the cord when they installed the stove . I would check the connections periodically as to avoid another situation like this .

Parts Used:

Terminal Block Kit

brendan from lebanon, NH
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers, Socket set, Wrench set

Was this instruction helpful to you?

Thank you for voting!

Broken front glass

Unscrewed frame and dropped in glass...easy

Parts Used:

Exterior Oven Door Glass - Black

perry from talladega, AL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

Was this instruction helpful to you?

Thank you for voting!

Spilled 1/2 gallon Hot wax on stove

Took door apart to clean inside of glass door. scraped most of the wax from the stove 99%. Could not get the last 1%. Cleaned all parts. Put door back together again, put the door seal on after I got the right one. Had to reorder a new seal(one that was actually made for that model) messed up the first one and whalla! Took about 3 weeks to clean off the wax from stove and the surrounding area. Stove is good as new. Thanks for the quick service. Would definitely recommend and use you guys again. Thank You.

Parts Used:

Range Oven Door Gasket

Roman from West Chester, PA
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers

Was this instruction helpful to you?

Thank you for voting!

I shattered the exterior oven door glass (black)

This was the second replacement glass I've bought, but I'm unsure if the first one was from PartsSelect or GE directly. It was a couple years ago when I purchased the first one. The first one popped in rather easily. I scraped out the rust and debris that had built up within the lower metal track and then inserted the glass. By pulling upwards on the door handle I had just enough room to pop it into the upper plastic tabs. The second door I bought was harder. I truly feel the second was larger. I tried the original procedure, but there was significantly more glass at the top, and I couldn't push up on the handle to even clear the handle itself. I removed the glass to re-cleaned the lower track, but it was clear of debris, so that wasn't the problem. I had to completely dismantle the outside plastic frame, insert the window and put it back together. It did fit after that, but now the door scrapes at the top ever so slightly when you shut it. Overall I'm very satisfied, since the oven is older now, but looks great again.

Parts Used:

Exterior Oven Door Glass - Black

noah from Canal Fulton, OH
Difficulty Level:
Very Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set

Was this instruction helpful to you?

Thank you for voting!

Stove drawer rear guides broken

Installed new guides with a nut driver without any problems.

Parts Used:

REAR SUPPORT

Robert from Shakopee, MN
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

Was this instruction helpful to you?

Thank you for voting!

Oven light wire broken, damaged socket

Remove light bail, glass cover held by two nut screws. Pull socket, removed clips in back, replaced wire connectors, placed new socket in, then glass cover and bail. Wire connected in back, cover plate replaced.

Parts Used: