JB655DK2WW General Electric Range - Instructions

Ordered window pack from PartSelect then removed oven door from front of stove, then removed back of door and silver backing and glass pack. Dropped new glass into place. Replaced all backing,put door back onto stove. Tip. When removing screw keep them separated from each other as not to get mixed up when putting everything together. Good Luck, PartSelect has all the parts you need, this my second getting a part from them.

Unplug range, pull out to access back panel. Remove enough screws to access the burner switch. Remove knob, 2 screws hold the switch, remove them. You can now pull the switch out the back. It had 2 electrical plugs remove them. Install on new switch and put back together. The switch I got was exact replacement, thanks partselect

Unplug range and pull it out to access the back. Pull knob off bad control at front making sure to check the orientation of the rod the knob goes on—it matters—and remove two brass screws. Then remove the four hex screws holding the top metal panel on at the back of the range (two have washers) and lift the panel off to expose the controls. (I then took a photo of the switch in situ to remember its orientation and how the wires were connected.) Use pliers to remove wires, then connect up and install the new switch, and put the brass screws back in at front to hold it in place. I used the pliers to turn the rod to the correct orientation before putting the knob back on. Reinstall the back panel with four hex screws. Plug the range in and test.

FYI the directions for accessing the infinite switch that came with the range also had me remove two screws under each side of the front of the control panel, but as far as I could tell that wasn’t necessary.

I am a 69 year old woman. I watched the Repair Clinic YouTube Video before I started. I then pulled stove away from wall and unplugged it. Took off oven door and removed the top oven rack. Loosened and removed the screw holding the temperature sensor located inside at the top center back wall of the oven. Pulled the sensor through the opening until the plastic plug came through. Unplugged and removed it and plugged in the new sensor. Fished it back through the opening. Replaced the bracket to the back wall of the oven and tightened the screw. Replaced the oven rack and stove door. Plugged it back in and moved it back into place. I turned on the oven and let is heat for over 30 minutes and the internal temperature was correct with the setting.

Removed two screws and unplugged electrical connectors to the baking element. It was that easy.

The draw pictorial was not very clear. I orderd the two rear supports for the over storage draw, not sure they were correct.
They were correct and the design had been upgraded to add strength to the support.
The draw is now operational..better then ever.

Removed back panel screws, removed back panel, removed screws of the control board, remove control board, heated glue and tore off plastic face plate, placed face plate on new control board, installed new control board, moved wires from old control board to new control board, test out oven, reinstalled back panel

My oven bake element melted one day. I had my husband replace it and for a short while it worked. Then it quit but then our broil element would not shut off. My husband said that it might be the heat sensor. We checked here in town and that element cost over $80. Since we have order from Parts Select before we decide to do so again. When we received the heat sensor my husband replaced it taking out the original heat sensor. This did not work as the broil element still would not turn off. I call the repair man and I found out that the initial melt down of the bake element also effected the main circut board that had to e replaced.

Unplug the range, remove the screws on the top third of the rear cover, remove two screws from the controller on the front side of the range, hold the rear cover open and pull the controller out of the back of the range, then unplug the two connectors from old controller. Plug the connectors into new controller, secure controller with screws on the front of the range, replace the screws on the rear cover, plug the range in.

First turned off power at breaker box. Pulled stove out to remove the half dozen hex screws on the back panel.(some nuts were stripped)Removed old oven sensor inside oven held by one hex screw and replaced it with the new part. Oven works great now! Repair job was done by husband Mike.

First; turn off breaker to stove.
Second; remove two Phillips head screws that hold the top on, located in front, underneath, will have to open the oven door to see.
Third; prop the top up.
Four; disconnect wire clips of old element.
Five; plug in new wire clips of new element.
Six; unprop the top and realign the top.
Seven; replace the two Phillips head screws to secure the top, then close oven door.
Eight; turn breaker back on.
Done and Back in Action! You Can Do This!

Tried GE onoine parts department first and ordered the wrong part, then tried the customer hotline and they referred me to the right part but didn't explain that the design had been modified (the drawings had not been updated). I found an explanation on Part Select AND the parts were cheaper. Part Select sent the part, the necessary screw, and an appropriate instruction manual. Each support took less than a minute to screw in with a socket wrench.

I viewed the video available through part-select. The most important thing I learned to do was to change one wire at a time instead of removing the old switch completely and then installing the new one. With 5 wires involved, it was really simple to install and not have to remember which wire went where. I was surprised how easy it was and it works wonderfully!

Disconnect power, then remove racks from oven, locate heat sensor by the broiler element. Use ratchet with extension and correct socket to remove the bolt directly under the heat sensor, pull the sensor out till you see the plug, disconnect the plug and then connect new sensor to it push wire back thru and then rebolt the new sensor on, thats it...

Unplug stove.2 screws out ,lift top ,disconnect bad element, connect new element, put top down .2 screws in .plug stove back in...EASY PEASY