JB645DT2BB General Electric Range - Instructions

Identified part and part # using schematic found on GE website, contacted PartSelect and confirmed part number, ordered and paid for part. Two days later I recieved part. Unplugged stove, removed two screws on bottom side of front panel and two on top back of same panel, pulled panel forward, pulled the control knob off, removed two small screws that hold the control switch in place, situated new control switch next to bad switch and removed one wire at the time from the bad switch and connected to the same terminal on the new switch. Put everything back together and Bingo, works like a new one. Thanks PartSelect for the friendly, personal phone service, the fast shipment and competitive pricing on my part.

Took part out of package, looked at instructions and followed them. Required a screwdriver to screw part on to the drawer.

Parts arrived in record time and the right parts. The detailed diagram was so helpful in finding exactly the part I needed to order. Was so easy my girlfriend with no mechanical or electrical experience completely helped me through the entire project. She secured the electrical breaker to the range, and I had the top back to the oven removed. I showed her how the little white box simply slides off the lens cover, then replaced the new one in the holes and slide it back on. Secured the back and she turned on the breaker back on...and all lights work. Thanks for making this project easy, simple and quick.

This was the second replacement glass I've bought, but I'm unsure if the first one was from PartsSelect or GE directly. It was a couple years ago when I purchased the first one. The first one popped in rather easily. I scraped out the rust and debris that had built up within the lower metal track and then inserted the glass. By pulling upwards on the door handle I had just enough room to pop it into the upper plastic tabs. The second door I bought was harder. I truly feel the second was larger. I tried the original procedure, but there was significantly more glass at the top, and I couldn't push up on the handle to even clear the handle itself. I removed the glass to re-cleaned the lower track, but it was clear of debris, so that wasn't the problem. I had to completely dismantle the outside plastic frame, insert the window and put it back together. It did fit after that, but now the door scrapes at the top ever so slightly when you shut it. Overall I'm very satisfied, since the oven is older now, but looks great again.

replaced insulation

Followed the example picture on the part bag. Anyone could do this, incredibly easy. Took about 4 minutes to install both sides.

Removed oven door. Removed 2 screws from heat sensor on rear upper wall of oven. Pulled unit out to access rear of unit. Removed six screws on shield on back of unit. Dis connected heat sensor wire and pulled old sensor through from inside of oven. Feed wire of new sensor through from inside and plug in. Everything in reverse. I also had the gas(propane) company come out and check the pressure coming out of the "low pres." regulator. It was low, they changed the regulator.

Disconnect the range from the mains. Open the door. Remove the single screw holding the temperature sensor - this is located on the back wall on center and is screwed to the broiler mounting plate. Remove the four screws holding the boiler element and allow it to hang down on the wire; this exposes a space to feed the wire through later. Now move to the back of the range and remove the six screws that hold the central cover plate. Now push the insulation to up out of the way and you can disconnect the temperature sensor, pull it out through front, insert the new one and connect it. Reassemble in the reverse order. Mine worked perfectly!

Easy to install replacement parts using the screws provided.

Repair was very easy - less than a few minutes - just had to screw in 2 screws to the new drawer supports.

Really easy fix. Unplug oven. With a 5/16 nut driver take the 5 screws out of the center long tin cover and remove. Unplug little white temperature sensor plug located between broil heating element. Open oven door and remove one screw holding temp. sensor using same nut driver and simply pull out old sensor. Install new sensor. It's that easy. No more f2 been working like a champ!!!

Disconnected power supply. Removed damaged element by releasing retainer clips and unplugging wire contacts. Replaced with new element.

Installed new guides with a nut driver without any problems.

Unplugged from wall outlet, then opened oven front door. Reached in and removed two screws. Pulled oven sensor threw and detached electrical connector from old sensor. Plugged in new oven sensor and reversed removal procedure. No more Flashing F2 and oven temperature came to ready. Very easy.

Simply removed drawer and lined up the newsupports. Made sure the guide pin was lined up and installed with single screw