All Installation Instructions for General Electric Range JB620SR7SS

Knob part broke on & off switch.Got a nee

Got a new knob.

Parts Used:

Knob

Sandra from Saint Johns, AZ
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

The light socket cup could no longer hold the bracket that holds the light cover in place.

I watched a video of a similar model to familiarize myself with the required steps needed. I opened the back and disconnected the power cord and ground wires connected to the removable socket I then removed the lightbulb and removable socket from the oven interior side. I then removed the defective light socket cup and replaced it with the part I purchased. After replacing the removable socket and lightbulb, the bracket holding the light cover functioned perfectly with the new light socket cup. Final steps were to reconnect the power and ground wires to the removable socket. I then replaced the back cover over the light socket cup area. One word of advise. Be very careful when removing and reconnecting the cables to the removable light socket.

Parts Used:

Range Light Cup

Roger from ALPENA, MI
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Socket set

1 person found this instruction helpful.

Was this instruction helpful to you?

THE FACE PLATE IS HARD TO GET OFF THE OLD CONTROL BOARD. USE A THIN KNIFE

THE INSTRUCTIONS THAT COME IN THE EMAIL ARE VERY GOOD. BE SURE TO TAKE A PICTURE OF THE WIRING.

Parts Used:

CONTROL OVEN TO9

Melvin from WEBSTER, TX
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers

1 person found this instruction helpful.

Was this instruction helpful to you?

Light burnt out.

Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.

Parts Used:

Light Bulb - 40W

Roscoe G from ROCHESTER, NY
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

2 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Replacing handle spacer

This one is simple. unscrew a portion of the door, install the spacer and screw back together. Worked well.

Parts Used:

Spacer

Sherry from SAINT PAUL, MN
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Broiler coil burnt out

It was just a matter of removing 5 screws that attached the broiler coil to oven top. Then carefully removing coil so as not to cause wires attached to fall into the back of the oven. Needed an extra pair of hands to hold coil while i guided the wires back thru the opening. All that was left to do was to secure the broiler coil to oven. All completed in less then 30 mins. A lot easier then originally thought. And, a lot cheaper then getting a repair person to do the job.

Parts Used:

Broil Element

Howard from LEXINGTON, KY
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

2 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Not Reaching Temperature above 300 Degrees

Take off 6 screws of back cover of the range, unplug the white wire. Go to the inside of oven, pull out racks. At the top of the oven is your Broiler element, in the center you will see a rod sticking out with one screw holding it in place. Take out screw and pull temperature sensor out toward you. Reverse steps to put it back together.

Parts Used:

Temperature Sensor

Ron from SAN TAN VLY, AZ
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

1 person found this instruction helpful.

Was this instruction helpful to you?

baking element was burned out.

unscrewed element from back of oven disconnected power source. Replaced new element & screwed new wires onto back of oven. Took 5 mins. Works like new. I am 73 yr old female so anyone can do it!

Parts Used:

BAKE ELEMENT

cynthia from CLAWSON, MI
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

BASE OF BULB BROKE OFF & WELDED TO SOCKET

PULL RANGE OUT FROM WALL & ALSO REMOVED OVEN DOOR BY SLIDING UP. WORKING FROM INSIDE OVEN & ALSO BEHIND I REPLACED PART . ALWAYS " UNPLUG " RANGE BEFORE YOU START.

Parts Used:

RECEPTACLE PUSH-IN

NEIL from ROCKY POINT, NY
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers

1 person found this instruction helpful.

Was this instruction helpful to you?

8' ELECTRIC ROUND HEATING ELEMENT

THE TWO 8' ROUND HEATING ELEMENT
1. LIFT THE LID OF THE STOVE FROM THE SIDE. SOMETIMES YOU MIGHT HAVE TO PRY IT A LOOSE. BE CAREFUL HOW YOU LIFT IT FROM THE BOTH SIDES WITH A FLAT SCREWDRIVER.
2. BECAREFUL HOW YOU PRY THE WIRING FROM THE OLD HEATING ELEMENT. THE WIRING IS FRAGILE. REMEMBER THE STEPS YOU TOOK TO TAKE A LOOSE THE OLD ONE. I HAD MY SON TO HELP ME BECAUSE I FIRST PULL THE CLAMP BACK WITH THE SCREWDRIVER AND HAD HIM TO HOLD IT TO OLD ONE STILL HOOK UP TO THE WIRING. I PLACE THE NEW ONE IN THE CLIP. THEN I TOOK ONE WIRING AT A TIME TO THE NEW ONE.

Parts Used:

BAKE ELEMENT

Lee from Calumet City, IL
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Bake button stopped registering

This was simple enough to repair for me, a relative novice. Just remember you need a nut driver to take the back panel off, take a photo of the existing board so you remember which wires go where, and you definitely need a hair dryer to heat up the sticker on the old board so you can remove it and put it on the new board.

Parts Used:

CONTROL OVEN TO9

Ryan from COHOES, NY
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers

1 person found this instruction helpful.

Was this instruction helpful to you?

Hot burner light lens broke off.

Pull range away from back wall. Remove panel behind control knobs by removing the screws that hold it on. Find hot burner light that holds lens. Remove broken part of lens. Insert new lens into hole on front of control panel and into hot burner light receptacle. Replace back panel. Slide range back into place.

Parts Used:

Lens

Charles from NEKOOSA, WI
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Change bulb

Easy

Parts Used:

Light Bulb - 40W

Louis from LEAGUE CITY, TX
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver

3 of 8 people found this instruction helpful.

Was this instruction helpful to you?

Original broil element had broken

Using a set of nut drivers, I unscrewed the element from the back of the stove, I unscrewed the thermometer, and unscrewed the brackets holding the element to the top of the oven compartment.

After the element was free, I pulled it out of the back of the oven, exposing the wiring. Using pliers, I disconnected the two wires, retrieved the new element, and re-connected the wires to the new element.

I reconnected the thermometer, pushed the element back into the oven, reattached it to the back of the oven and the brackets to the top of the oven compartment.

Parts Used:

Broil Element