All Installation Instructions for General Electric Range JB400DP3BB

Broken rear drawer support

Installed the new brackets at the back of the drawer with the 2 screws provided. The new rear mount design is much better than than the old side mount.

Parts Used:

REAR SUPPORT

Jesse from Knob Noster, MO
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

oven door gasket needed replaced

Ordered the part, it arrived and 5 minutes later it a complete installation

Parts Used:

Range Oven Door Gasket

Mary from LONGS, SC
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

The storage drawer came without supports.

I just removed the drawer and installed the rear supports as instructed on paper included with the part.

Parts Used:

REAR SUPPORT

Dock from Aurora, CO
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

2 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Bad Line fault displayed on range clock

1. Unplug the range power cord from the outlet.
2. Moved range away from the wall and countertop.
3.Using a nut driver removed the 2 screws on each side of the removable panel on the back side of the control knobs and clock.
4. Using a phillips head screwdriver remove 2 screws on top side of the back side panel.
5. Using a nut driver remove 4 screws that secure the main control board in place.
6. Take photo of the wiring on the main control board if not color coded.
7. My control board, and the replacement board were both color coded with the color with the wire placement on the rear of the board.
8. Remove wires with needle nose pliers.
9. Using a hair dryer, heat the plastic control panel face plate that fits onto the front of the old control board.
10.With a putty knife carefully pry the face plate from the old control board.
11. Install the control board face plate onto the new control board.
12. Install the color coded wiring in place on the back side of the control board.
13. Replace the control board into the range, and install screws, and rear panel of the range.
14. Plug cord into outlet and test range for proper operation.

Parts Used:

CONTROL OVEN TO9

Vincent J Paola, from GREENWEL SPGS, LA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Plastic guide Broken

replaced Plastic Guides

Parts Used:

Bottom Drawer Guide

NICK from Vernon, CA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

9 of 25 people found this instruction helpful.

Was this instruction helpful to you?

Oven board went out

One wire at at time then used my razor blade to get front off stuck right back on

Parts Used:

CONTROL OVEN TO9

Jackie from TICKFAW, LA
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers

1 person found this instruction helpful.

Was this instruction helpful to you?

just want new parts

very easy and clean.

Parts Used:

BOTTOM TRIM CHANNEL BLACK

Minnie from hurdle mills, NC
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set

1 person found this instruction helpful.

Was this instruction helpful to you?

Knob part broke on & off switch.Got a nee

Got a new knob.

Parts Used:

Knob

Sandra from Saint Johns, AZ
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

The light socket cup could no longer hold the bracket that holds the light cover in place.

I watched a video of a similar model to familiarize myself with the required steps needed. I opened the back and disconnected the power cord and ground wires connected to the removable socket I then removed the lightbulb and removable socket from the oven interior side. I then removed the defective light socket cup and replaced it with the part I purchased. After replacing the removable socket and lightbulb, the bracket holding the light cover functioned perfectly with the new light socket cup. Final steps were to reconnect the power and ground wires to the removable socket. I then replaced the back cover over the light socket cup area. One word of advise. Be very careful when removing and reconnecting the cables to the removable light socket.

Parts Used:

Range Light Cup

Roger from ALPENA, MI
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Socket set

1 person found this instruction helpful.

Was this instruction helpful to you?

Oven no longer working after running the self clean option. Only Stove top burners worked

I began by turning off the breaker in the panel.
Slide the oven out into the open area.
Removed 3 screws in order to remove rear top panel.
Took 2 pictures of the wiring location on the PCB
Removed all wiring going to the circuit board total of 8.
Removed 4 screws in order to remove bad PCB.
Remove faceplate from bad PCB (you will need to place this faceplate on the new PCB.

To Install.
Reverse steps above

Parts Used:

CONTROL OVEN TO9

Dominick from THORNWOOD, NY
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Light burnt out.

Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.

Parts Used:

Light Bulb - 40W

Roscoe G from ROCHESTER, NY
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

2 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Replacing handle spacer

This one is simple. unscrew a portion of the door, install the spacer and screw back together. Worked well.

Parts Used:

Spacer

Sherry from SAINT PAUL, MN
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Not Reaching Temperature above 300 Degrees

Take off 6 screws of back cover of the range, unplug the white wire. Go to the inside of oven, pull out racks. At the top of the oven is your Broiler element, in the center you will see a rod sticking out with one screw holding it in place. Take out screw and pull temperature sensor out toward you. Reverse steps to put it back together.

Parts Used: