Models > J764Y1 > Instructions

J764Y1 General Electric Range - Instructions

All Instructions for the J764Y1
16 - 22 of 22
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The Upper oven the lower element went out.
Unscrewed the prongs to the old element. When the new element showed up I put the new element back in again. Had no problem with the replacement and my oven works great.
Parts Used:
Upper Bake Element
  • Norma from SAN JOSE, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver
Was this instruction helpful to you?
Thank you for voting!
Upper Oven Lower Element Burned Out
Took off the oven liners, took out 2 retaining screws, pulled out element, removed wires, reversed procedure, easy
Parts Used:
Upper Bake Element
  • ROBERT from SEATTLE, WA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver
Was this instruction helpful to you?
Thank you for voting!
The oven coil burnt out visibly sparking at the failure point on the coil
This model has a top oven and a bottom. The repair was to the top oven. I shut off the electricity to the oven at the circuit breaker box.I removed the grates and unscrewed the two screws holding the burner in place. I gently pulled the burner free along with its two attached wires. I removed the two screws that retained the connections to the burner. I installed the new burner in the reverse order. Turn on the circuit. Good to go.
Parts Used:
Upper Bake Element
  • Mark from Fort Wayne, IN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers
Was this instruction helpful to you?
Thank you for voting!
Old element was burned out. Haaven't figurerd out how this happened.
Just unpluged the old one and detached the wires. put the new one in and used a socket wrench to rewire it. . Very easy and was shipped in perfect condition and easy to replace. Very pleased.It fit perfect and oven works just fine. Thank you so much for the service which was very speedy. It was packed to perfection.
Parts Used:
Upper Bake Element
  • Pauline from Helena, MT
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Socket set
Was this instruction helpful to you?
Thank you for voting!
only half of burner working
Replaced the old with the new following directions (mostly).
Parts Used:
Tilt Lock Hinge Mounted Surface Burner Kit - 6"
  • KENNEDY from OCEAN GROVE, NJ
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
The instructions on striping the wires was slightly confusing.
I stripped one wire on the first burner. Then I realized that the terminals were the ones that could be left. Finding a replacement terminal has proved to be difficult. Once I realized my mistake I could change the other three burners very easily.
Parts Used:
Tilt Lock Hinge Mounted Surface Burner Kit - 6" Tilt Lock Hinge Mounted Surface Burner Kit - 8 Inch
  • Katherine from Berkeley, CA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers, Wrench set
Was this instruction helpful to you?
Thank you for voting!
Bad Burner
There was no burner listed like 40 yr old burner that failed. Got one the same size and connections. Cut old burner out of the stainless steel ring and new burner fit right in. New burner works great
Parts Used:
Tilt Lock Hinge Mounted Surface Burner Kit - 6"
  • Grady` from Titus, AL
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the J764Y1
16 - 22 of 22