J33202 General Electric Range - Instructions

Finding a replacement element for a 30 year old GE electric stove was difficult to find. I was overjoyed when I found a replacement on Partselect! It was a simple "Unscrew, reattach wires and install" all in about 10 - 15 minutes all with a nutdriver. Plug in elements are common but to find one with screw connections is not easy, THANK YOU PARTSELECT! A $48.00 investment (Element with trim ring) was worth the cost compared to a $1,400.00 replacement. You just made a loyal customer, again, Thank You.

Lenny
Nazareth, PA

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the four wires The element i request was 3 elements and i received two element but it was very easy i connect only the 3 wires.

Both the eight inch burner and the the six inch burner were not an exact fit. I used the old rings and the new burners. The eight inch burner fit well with the new drip bowl;however, the six inch burner did not fit with the six inch drip bowl and I had to grind off about an eigth inch from the diamiter of the drip bowl. I replaced most all the wiriing and after I get the lower oven element rebuilt it will be ready for a test drive ..can't wait!

I removed the unit easily with anut driver, however the unit also supported the thermo-link. I had to use the hack saw to relieve a small opening for the thermo-link to pass through. No real problem. Then a few holes to be drilled to attach the 'link' to the base of the broiler unit.

BUT-I went into the website listed on the box. GEAppliances.com Guess what? Their price was twice yours!!

Broiler element arrived at my door 3 days after ordering which was nice. Apparently the billing dept. is out of the USA so don't be surprised, like I was, to find a suspicious looking charge for a currency exchange fee (mine was 42 cents). I had to drill two new screw holes in the base of the new element in order for it to fit my oven. I also had to use heavy wire snips to cut off about an inch of the top of the new element base. The female electrical connections also had to be spread out with needle nose pliers since the new element connections were slightly thicker. With all of the issues I had I was frustrated and it took about two hours. On the other hand, the part works perfectly and was priced right. Hopefully it will fit perfectly out of the box for your oven.

I looked on Youtube for a how to video. It was accurate but the screws in my oven were NOT phillips head screws, they turned out to be sheet metal screws. I used pliers at first which was a PAIN but then I borrowed a socket wrench from the neighbor that was MUCH better!! I had wanted to do it myself to prove to my husband and son that I could but I ended up needing their help because the screws were so tight.... But we did the repair ourselves!!!

This part has the trim ring attached. My old element had the trim rim detached. This new part still fit my stove top and works fine.

Parts arrived bent and element had tape residue on it. After approximately 1 hr. I was able to clean, make parts straight and install it.

First I removed the screw that holds the element in place. I then pulled the element out about 3 inches and disconnected the three wires. Then I just had to do it in reverse. EASY!

First I shut off the circuit breaker for the oven then removed the screws that hold the element in place. The element was pulled out about 3 inches and unscrewed the 2 screws to disconnect the two wires. Upon receipt of the new element, I simply reversed the above process and the oven performed like new. Very easy, very quick and very grateful to have the oven operating again and it was a very inexpensive fix.

removed 2 nuts holding the element in the oven. removed 2 screws that secured the wires to the element. installed the new element in reverse.

The customer service at PartSelect.com is wonderful. They assisted me to located a part for a 40 year old oven. Took only a few minutes to take the old one out and put the new one in. Process was pretty self explanitory.

I unscrewed the old burner from the stove, took off the three wire to the heating element marking down where each colored wire went, taped off the exposed wires, ordered the new burner, and waited for it to arrive. When it got here, I installed it, and believe it or not, the new burner works just fine!. End of exciting repair story.

Replacing the part was fairly simple. Do not forget to dis-connect the element from the back.

turn off breaker in electrical panel....remove stove socket from outlet....remove rear panel from stove....undo wire connectios from broiler element....inside the oven, gently move thermostat wire out of the way....unbolt broiler plate from rear wall....remove broiler hanger and then broiler element....reverse procedure and you're all set.