J303V4 General Electric Range - Instructions

Lifted burner element to remove pressure on ring and drip bowl. Removed old parts and replaced in reverse order. This not intended to sound sexist, but my wife who is not particularily mechanically inclined performed the task on her own.

the replacement items fit really good. It was a matter of remove and replace,

Just lifted the electric components Remove drip plans and trim rings and replaced with new drip pans and trim. Your company was incredible in there delivery of the parts..One day. You made my husbands very happy.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. connected the wires to the new element. pushed the element back in place the screwed it back to the back of the stove.

Removed the plug from wall socket.
Removed door to oven by lifting it straight up while partially open, in locked position.
Remove Baking shelves.
Removed 2 screws @ the back of element where it goes into the ovens back wall with a nut wrench and gently pull the element towards you until wires are exposed.
Using a flat blade screw driver hold on to the end of the element near the end with the screw and support it as you un screw the wire so the end of the element does not bend as you turn the screw.
After both wires are removed, remove the old element.
Install the new Element in reverse.
Very Easy!

Shut power off. Removed two outer screws, pulled heating element forward and removed two more screws. Ordered part and it arrived in three days. Installed in reverse order of removal. Easy fix. Cost was reasonable.

First I removed the two screws that hold the element in place againts the oven wall. I then pulled the element out about 3 inches and disconnected the two wires. These wires were screwed into the element so it was important to order the correct screw-in type replacement element. I pushed the wires back into place and screwed in the plate that holds the element against the oven wall. It was very quick and easy.

I simply removed the 2 mounting screws, pulled the element out a few inches, disconnected the 2 screws holding the wires to the terminals and reversed the order for assembly.

REMEMBER to turn off the breaker at the panel because the wires are still hot even though the oven control itself is off (trust me!!!).

Excellent service and fast delivery from partselect.com........ I'd gladly deal with them again.

The hardest part of this entire repair was locating the right socket and explaining why/how I burned my fingers (yes I had to touch the element to prove to myself it was that easy to fix and worked). 4 screws, 1 replacement part 5 minutes no cussing. This was the easiest repair I have ever done.

First turned off the circuit that controlled the power to the Stove/Oven.
Then I removed the screws that hold the element in place.
I pulled the element out a few inches and disconnected the wires.
I attached the wires for the new element.
I replaced the screws.
I turned on the circuit.

And to reward myself baked a Coffee Cake. Yum!

Removed 2 screws with nutdriver.Pulled element out to expose wiring and disconnect 2 wires also with nutdriver. Reverse process. Unit reaired.

removed the old heating element which had about two screws and two connecting wires and replaced it with the new one. I twas so fast and easy. I thought I was going to need a new Oven!!!!!Thank goodness for your website!!!!!

First I removed the 2 mounting screws that mount the element to the back wall in the oven, then pulled the element out about 4 to 5 inches, then removed the 2 screws attaching the wires to the element, then reversed the process to instal the new element. The only tool reguired was a 1/4 inch nut driver. Did the job in about 5 Minutes. The replacement fit and works perfectly.

I was lucky to look at other repair stories because I forgot to turn off the power!!! Nothing happen to me, but it was as simple as everybody else said. Unscrew the two screws, pull out element, unscrew another two screws and put back together in reverse order. Viola, the oven was back in working order just in time for a major event the next day. Thanks everybody for their tips and partselect for fast shipping.

I turned off the breaker, removed two screws that held the element in place, pulled it out about four inches, disconnected the screws securing the wires to the element. Removed the old element, placed the new one in the oven and reversed the procedure.