J301P2 General Electric Range - Instructions

I removed both screws to remove lower element, and measured it prior to ordering the replacement.
Then in a few days it arrived, and I installed it. The new element had small bolts rather than screws the original used to attach both wires. A flashlight was necessary in locating an keeping an eye on the wire ends, to keep them from being pulled inside the back cover, as the bolts were attached.

Following common sense, I removed the broken bake element by first removing two retaining screws and then disconnecting the element from the internal wires using a nut driver for both operations. The new element was installed in reverse order first using a screwdriver to attach the element to the internal wires (the new element had embedded threaded openings and came with two new machine screws) and then using the nut driver to secure the element to the oven wall.

I unplugged the stove, unscrewed two nuts, pulled the two wires forwrd and disconnected them. Attached the wires to the new burner and it works fine!

First I turned off the breaker to the stove in the breaker box and then removed the two small screws that hold the element in place. I then carefully pulled the element out about 3 inches and using a 1/4 inch socket, I unscrewed the screws that held the wire on the bake element. There were two wires held in place with 2 small screws. I made sure that when I unhooked the wires they did not pull back into the back wall of the stove. I then removed the old element and put the new one in its place, hooked the two wires back up, pushed it back in place and secured it to the back of the wall of the stove with the other two screws. I then turned the power back on and presto, it worked perfectly. Like new again.
Thanks for everything.

The repair was a bit difficult because the screws connecting the wires to the element were small threaded bolts and no slot for a screw driver. They were very difficult to break loose - that's when we used the Liquid Wrench and waited. Other than that, the repair went smoothly. It is better to remove the oven door, if you can, otherwise the rear of the oven is not as accessible. It is also a good time to change the light bulb.

Simply removed the old one and replaced it with the new one. Part Select was the only company that was able to identify the part without the Model Number. The Model number was
worn off and unable to read. After going through several
on-line parts dealers, Part Select was the only company that could identify the part I needed. The repair was simple and
short. My old stand by oven is in operation again.
Thanks, Laura

Unscrewed four screws, removed old element, replaced with new part, done!

I took the old element out, compared it to the pictures of the GE replacement elements, identified the correct one and ordered. It came I installed it in 15 minutes and it works just right. I was unable to determine the model number of my old oven so the pictures of replacement elements were invaluable. Thanks for making it so easy to avoid calling a repairman.

It was so easy, we got on the General Electric web site and entered the old model number, found our match and ordered the part. It came 3 days later and it was so easy to remove the old one and install the new one, only two screws to remove. Saved a lot of money by doing it ourselves! Thank goodness for websites like this!!

Remove the old element by removing one screw and inserted new element and replaced the screw.

It was quite simple after the part arrived. I actually had forgotten what the connection was because one wire was yellow and one was red. After calling the number that I had to no avail. I went to the computer to ask how to install the part. Installed in little to no time. Feel like a Jill of all trades. Bring on the next problem.

Element was in two pieces so it was obviously dead. I disconnected the stove from the power, I undid the two screws at the back of the oven and gently pulled the element out. There was enough slack to reach and pull the connectors apart. Done. I ordered the part from "PartSelect" and it arrived the next day. Unfortunately I ordered the element with "Screw" convectors as opposed to "push on" connectors. I bought a couple of connectors and cut off the original connectors from the wires in the oven and replaced them making absolutely sure they were well and truly tight. Two screws cam with the element from "PartsSelect (Thankfully). Connected the wires and screwed it back into place. Stood clear, plugged it in and turned it on to max. Worked just fine, Thanks

first i removed two screws pulled that hold the element in then pulled element out about 3 inche disconnected the two wires now hot meals thanks

Undid two screws to pull the element out, and another two to unhook it from the wires. Reverse procedure with the new element and baked some muffins. The hardest part about this repair was getting the part. I typo'd my shipping address and had to knock on a neighbor's door!

I replaced the element. The new part arrived within 48 hours of being ordered. It worked. The part that sticks out the back of the oven with the connections was a little shorter on the new element which made it more difficult to put the wires on but it was not too difficult.