J2BP85SEL2SS General Electric Range - Instructions

Remove the top grate and remove the top burner plate and then pull the burner out and remove the torx screw and adapter install onto the new burner and place back on the stove , good to go.

I remove the old thermostat and realized right away it was burned, the replacement was very easy to clip on

0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.

Step 1 pull the broiler completely out of the bottom of the oven. Step 2 unplug the igniter Step 3 remove 3 small screws to pull the burner tube completely out of the oven. Step 4 replace the igniter and repeat steps to install burner tube back into the oven.

replaced lights in refrigirator and freezer

Very was ti replace racks and knobs. Very fast mail service

Removed two screws to remove old bottom. Insert new oven bottom and re-attach screws.

Pulled the gas stove out so that I could shut off the gas valve and unplug the power cord. Job was made easier by removing the oven door (which just slides out). I took the 2 screws out that held the old igniter in place. Went to the rear of the range where there was a small 3"X2" electrical cover for the igniter, and disconnected the wire leads from the wiring harness. I then pulled the old igniter out through the oven front. Fed the new igniter wires through the back of the range and plugged the new igniter in. Reinstalled the electrical cover in the back of the range, attached the 2 -1/4" screws to reinstall the igniter inside the broiler. Put back the oven door. Turned the gas valve back on and sprayed on a soapy solution to check for gas leaks. Plugged the electrical cord back in. Pushed range back in place, Turned broiler on. Wait for a few seconds till the gas comes back thru the line. Works great Our stove was a GE Profile Gas Range. The part number for the igniter is WB13K21. We are very satisfied. Jim

Gasket front door frame off with old and on with new 10 Mins.
Gasket Assembly door takes time first need to remove the oven door need to lift up enough to clear oven door upright catches be careful door is heavy my need another person with lifting and lay the door on a flat surface like a table and they're a lot of screws to be undone remember were the go when reinstalling do not rush take your time do to you are working with sharp edges time 4 hours for remove door take apart but together and reinstall

Replaced the flat style oven igniter. First, I watched the video on your web site, and used it as a reference to make the repair. I did remove the oven door tho, as it made it easier to complete the work, the video didn't show the door being removed. The video was very helpful.

In general, other repair stories on this site collectively give a good description of the repair process. My words concern the decision that has to be made as to which element is bad - igniter or gas valve. To reach a conclusion about this question, I was comforted by the fact that I could measure the AC electric current through the gas valve which then let me decide that my problem was in the igniter. Since the circuit is a simple series with three elements, thermostat, igniter, and valve and the resistance of the valve unit was 1.0 to 1.2 ohms (per GE range equipment instruction which came with the range) by measuring the AC volts across the valve, I found (by dividing the volts AC across the gas valve (2.3 volts) by the resistance of the valve mechanism (1.0 ohms) that my old igniter was only supplying 2.3 AC amperes (instruction sheet states 2.9 amps. is needed to actuate the valve and further while heating of the oven is occurring the valve AC current will raise to 3.2 to 3.6 amps.). At 2.3 amps. the igniter will glow at a yellow color but will not actuate the valve. When you replace the old igniter with a new one you will enjoy to measure voltage across the gas valve once again and discover that the voltage rises to 2.9 volts and that the gas turns on and the heater tube gas is ignited.

Remove the existing burner and install the replacement.

Removed oven racks, removed lower oven shelf panel by using a flathead screwdriver and removed two screws on the back edge of the panel. Removed flat style ignitor (two hex head screws)from the gas burner tube using a 3/16 nutdriver. Disconnected two wires from the ignitor. Removed the two pin connector from the new ignitor, stripped the insulation to expose about a 1/4 inch of bare wire at the ends of the wire where the connector was removed. Installed the ignitor to the gas burner tube using the 3/16 hexhead screws. Connected the wires using porcelain wire nuts. Re-installed the lower oven shelf panel, flathead screws and the oven racks. Oven worked as advertised.

I thought I was being a total girl and was afraid of fixing my oven myself, but when it took forever to get my landlord to come over and fix my oven I ordered the part, got it in three days, followed the directions online and fixed it myself! Easy, easy! Turned off the electric, switched off the gas, unscrewed 2 bolts, unplugged the old switch, screwed in the new switch, replugged it and turned on the stove. Roasted a chicken and baked bread within minutes!

I deturmined that the flame starter was not pulling enough amps to open the gas valve (safety valve) . pulled two hand screws and removed floor of oven exposing the flame bar and flame starter. removed two screws on flame starter. removed lower pan drawer and disconected the electrical plug for flame starter. replaced in reverse order. easy.