J2B912SEKS General Electric Range - Instructions

I watched the repair video on YouTube and followed his instructions as much as possible. Went pretty well as I thought it would be harder. I’m pretty handy so, I was pleased.

Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.

Ordered part from customer friendly Part Select and received the replacement part within a few days, and installed it promptly. Wife is happy and stopped grumbling about oven bottom unsightly defect! Small price to pay for a happy wife! Ernie

Easy

Start by removing all screws 3 for each burner total of 15 t-15 bit is required then proceed to remove spark igniters 5 total slight pull next step would be to slide a screwdriver under top left and right side to remove top shelf. There you will have access to the parts you need to replace. When done just reverse installation instructions to complete

Removed burner and replaced

Would have been easy, but I should have checked the measurements more carefully as it didn't fit. But the service from Part Select has been excellent!

nothing to it.

called appliance repairman. He found problem and ordered new part. After 2 months waiting for part to get there, my husband got on internet and calld your number, and ordered what was needed. Now for the great thing. Within 4 working days we received what we thought we needed. but we had ordered the wrong part number. Got back on internet, went right to your web site, found the part that we did need, a flame spreader instead of the Deflector. called your service number, talked to a very nice person, again, told her what we did and ordered the correct part. Another great thing, we got that part the very next day. I returned the wrong part that same day. We then had our son install it and now we have a very nice working oven. Though out this very long ordeal, we talked to the applicance service people and got the same answer. The part has been ordered and it should be here next week. When we found your web site and called for the part, I called the appliance service and told them we had ordered the part ourselves and I would be happy to give her this information. THE VERY NEXT DAY she called us to tell us the part had fially arrived and they could come out the next day. Told them sorry but it as already taken care of. The very next time we need some part for any appliance we will call you first. Thank you for your very nice service people and the fast way that this all took place.

Remove bottom drawer,open oven door,take oven racks out,use flat tip screwdriver to remove two screws in back of oven. Then remove cover over burner and igniter.Reach under oven and unplug igniter,while down there use 1/4 inch nut driver and remove two screws holding burner. Then remove one screw inside oven in front of burner. Pull burner and igniter up and out of oven.I did not unplug stove or turn off gas some people may want to,if you have to move stove out to work on it

I ordered the oven rack on a Tuesday and received it the very next day - was wowed at the service.

Removed grill grates, gas distributors, etc. (just lift off). Used star screwdriver to remove screws (3 per burner for SML, 2 for power burner). Lift off stainless cover, which also lifts off the white sparkers I was replacing. Pull them off the wires (didn't need pliers, others said they did). Replace (make sure it is all the way on) and reverse your steps. White sparkers electrodes seemed loose when I put them back on, but tightened up when I fully secured the top back on. Make sure the wires aren't pinched underneath when you put the top back on. Recommended: If you've got one that isn't working, go ahead and replace all 3 (power burner is different) because the part is so cheap you may as well just do it now.

Open a HUGH box to get a smaller box that was surrounded by air bubble packing. Opened smaller box, removed the range's center rack and replaced it with the griddle.

just slipped it in

Husband actually did the repair, It went really well except he forgot to remove the heat shield from the old part to attach to the new bottom. (His mistake!)