All Installation Instructions for Inglis Range IRE32301

I snapped a bolt on the main power terminal block when connecting the pigtail.

Removed the small metal panel covering the main power terminal in back of the electric range. Removed the nuts holding the red, white and black electrical wires from the range using the appropriate socket (there will be two nuts on each bolt end). Removed the two screws holding the main power terminal block with appropriate screw driver. Connect the new main power terminal block to the range using the two screws. Reconnect the red, black and white electrical wires coming from the range using one nut for each wire. IMPORTANT: do no over tighten the nuts because the bolts could snap. Reconnect the pigtail and secure the small metal panel covering the main power panel.

Parts Used:

Range Main Power Terminal Block

Frank from Palm Coast, FL
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Socket set

3 of 8 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

cleaner

just needed clearner for the top of my glass top, the operator was very helpful I received my clearniner in 7 days thank you

Parts Used:

Cooktop Cleaner

Mary from Duarte, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

broiler pan missing

ordered new broiler pan

Parts Used:

2 Piece Broiler Pan

RAYMOND from JACKSONVILLE, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Oven temperature was 50 degrees off

Unplugged stove.
Pulled stove out.
Unscrewed screws and removed cover.
Removed & replaced sensor.
Reinstalled cover & screws.
Plugged in stove and pushed back in.
Only problem was when I pulled stove out, lid opened and disconnected the gas line to a burner.

Parts Used:

Oven Sensor

Gregory from BRIDGEBORO, GA
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

burned out stove eye, 6"

remove burned out eye, replaced with new eye.new eye does not fit exactally correct onto splash pan as point on end of steel " rod " not pointed enough to slip into mate on splash pan

Parts Used:

Standard Y-Frame Range Surface Burner

Robert from Birmingham, AL
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Both outside door handles turned very beige

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

Parts Used:

Spray Paint - 12 oz. - White

Howard from Boynton Beach, FL
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver

23 of 69 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

oven light not working

replaced light socket but did not repair problem. must have burned the motherboard.

pleased with service from your company.

Parts Used:

SOCKT-LITE

Richard from Gaylord, MI
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers

2 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

burned oven bulb

The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.

Parts Used:

Light Bulb - 40W

Ivanka from Atlantra, GA
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers

3 of 9 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

surface burner heating element broken

took out old element, replaced with new.

Parts Used:

Range Surface Element

Marlene from Charleston, SC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

slides on lower drawer were broken

I used a phillips screwdriver and replaced the part with one screw.Very easy and replaced my lower drawer under my oven,it tool about three to five minutes at the most and my drawer works fine now.Thanks for the instruction video on line, it really helped.

Parts Used:

Range Rear Drawer Glide

Leona R from Louisville, KY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Bad Receptacle

I had a receptacle melt in front of my eyes. I few questions later PartSelect.com showed me the part I needed and was checking out in less than 10minutes. Part arrived 3 days later and 20 minutes after that it was installed. I'm Amazing!!! No, PartSelect.com is AMAZING!

Parts Used:

Range Receptacle Kit

TROY from YPSILANTI, MI
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

2 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Inside Light would not work

Turned off CB for the oven,Remove the oven from the cabinet , remove the back of the oven, replaced the light Assembly. turned on CB for the oven, tested the light. and truned off the CB and replace the back and reinstalled the oven in the cabinet.

Parts Used:

SOCKT-LITE