IM115 Uni Ice Maker - Instructions

Unplug refrigerator power cord. Remove ice cube bin. Place wire signal arm in down (off) position. Ice Maker is held in place by two (slotted/hex headed) screws through keyhole slots over the top of Ice maker along the left side of freezer. Use mirror to locate screws then carefully loosen (do not remove) screws with a nut driver or screw driver. Lift Ice maker up and right until it releases from the screw heads. Unplug electrical connection. A flat screw driver may be required to loosen connector. Connect new unit electrical and Install new unit over screw heads and tighten screws. Replace Ice Bin and place wire signal arm in the up (on) position. Reconnect refrigerator power cord. After freezer cools down sufficiently it will start making ice.

I followed the video that came with my email receipt but i had to use the extra electrical adapter, there is no where to put the extra wiring so it is hanging next to the wall. I was glad I didn't have to unplug the fridge. just kept the wire up so no water would come out. It took several hours to start working and it doesn't make as much ice as the old one, but at least it works. It was a very informative video. Thanks

Went well overall. I really thought that you guys taking the time to create a very helpful video was awesome. Thanks for doing that! The only difficulty I had was that my old ice maker had the connection toward the front, while the new one was in the back. So I had to use the adapter and had so much extra wiring to bundle, and tie wrap, with little place to go with it that I got frustrated. Wish I just had the correct replacement wire to begin with. Nonetheless, we are stocked with a full bin of ice after about 3-4 days.

loosened two 1/4 in. screws removed ice maker unplugged harness. Plugged back in slid the replacement ice maker over the two screws secured. Done

instructions were very simple. Took about 10 minutes to replace the unit. Do NOT get excited about immediate ice because it took mine awhile to g et cranked up for full production. Anyone can do this! Saves about $150.00 in labor to have someone(no smarter than you) do it for you.

Remove back cover (5 screws )remove valve ( 1 screw ).Disconnect in and out water lines. Disconnect wire on solenoid. Install in reverse. Dont forget to turn off water.

I took 2 screws loose and undone water lines, replaced and reconnected everything. Real easy

1st my 72 year old husband has not had great success in repairing anything: electrical or plumbing. We got the part the next day. Had ordered it late one afternoon and had it the next morning in Wyoming. From the time we took it out of the box, disconnected the old one, plugged in the new one, remounted, it took less than 15 minutes. Amazing and it works great. Didn't need extra electrical connector, but tricky part on electrical connectors is to squeeze side to take apart and put back together. He used mirror to see the screws to loosen to take out and put back in ice maker. Next day our tray was full of ice. Good service/Good Product.

Tested for power and found the thermal cut-off bad. Installed new one.

first replaced dual solenoid, then ice maker. still not working. going to chase electrical next

Followed the video instructions posted below the product. Its a tight area to work in but it can be done. It did not immediately start making ice. I waited and waited.... 3 hrs 4 hrs still not filling up or making ice. Finally I decided to pour some water in the tray and see if it would freeze ice and dump it. It did and immediately started to fill up on its own after that! Its been working perfectly ever since! So dont be alarmed if yours doesnt work immediately and try pouring some water in it if yours doesnt being working within several hrs. I am happy I was able to do this myself and save repair man costs. Its just not work the cost they charge for older appliances.

1st a changed the defrost stat. Waist of time. Realized there was no evaporator above fan. Noticed ice was builing up behind ice maker near fill tube. Found if I shut off ice maker ice wasnt building up on fan. Moved fridge out unplugged fridge unscrewed plastic nut. Turned 90 degrees. Replaced tube locked in place . Screwed nut back on . Plugged in and turned ice maker on. Wife happy ice was back on and no noise.

The two screws that held the ice maker in place could not be seen do to there location. I could only get one hand inside do to space restriction.So I placed a mirror inside so I could see the screw heads and from point it was very easy to see and line up the nut driver on the screw heads. I then lifted it up and unplugged the wiring and installed the new ice maker. Works like a charm. Paul

This is the 2nd ice maker replace in the past 20 months. This installation was easier following the experience of the first replacement. The instructions are well written. The pictures or illustrations are difficult. The most challenging part of the installation is routing and fastening the wire harness. The illustration was not helpful. Overall, this is a repair most DIYers should be able to accomplish.

ice maker= replaced overload,microswitch and solenoid water valves.refrigerator=replaced the thermostat.Great price on parts,very fast delivery and parts were a perfect fit.You made the job very easy. John