All Installation Instructions for Inglis Dryer IJ70001

dryer worked but no heat

Initially we thought the problem was the igniter, so we ordered an igniter kit. Installed it but was unsuccessful. We then went on the websight and read further, about 50% of dryers with no heat but working had a problem with the thermal fuse.So we ordered the thermal fuse installed it, which was very easy, and success. Once the problem was diagnosed properly it was fast and easy. Recommend looking at the statistics for specific problem.

Parts Used:

Igniter Kit

Tracie from Culver City, CA
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins

18 of 20 people found this instruction helpful.

Was this instruction helpful to you?

lint filter shredded after 24 years

pulled out filter measured it looked on internet found this site ordered it threedays later BINGO new filter thank you!

Parts Used:

Lint Filter

barbara from merrick, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

18 of 20 people found this instruction helpful.

Was this instruction helpful to you?

Heat Would Not Come On

After replacing all the other fuses and sensors I finally replaced the Radiant Flame Sensor and it is working perfectly.

After replacing the other parts and the heat still not coming on I read somewhere that the Radiant Flame Sensor is a normal closed circuit and when I checked with a meter it was open. I would have saved a lot of time and money if I had read that earlier.

Parts Used:

Dryer Radiant Flame Sensor

Lynn from Novi, MI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

19 of 23 people found this instruction helpful.

Was this instruction helpful to you?

Broken push to stat switch

Removed back cover, removed broken switch, replaced with new switch, replaced back cover, told wife her dryer was fixed.

Parts Used:

Push-To-Start Switch

Charles from Fairfax, OK
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

18 of 21 people found this instruction helpful.

Was this instruction helpful to you?

dryer not working

After unplugging and removing the back cover from the dryer, locate the push button switch. Slide putty knife around outer cover to unhook catch. Replace with new push button switch. My dryer is still not working, but this was a simple replacement.

Parts Used:

Push-To-Start Switch

Maura from Newtown, CT
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

22 of 33 people found this instruction helpful.

Was this instruction helpful to you?

Door Gasket tore out

Put high temperature glue on first, then put door gasket over the high temperature glue and then let it set for 24 hours. It worked fine....

Parts Used:

Door Gasket

Manolak from MURFREESBORO, TN
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins

16 of 16 people found this instruction helpful.

Was this instruction helpful to you?

Handle broke on dryer filter

Got a new one

Parts Used:

Lint Filter

FRAN from ROSEVILLE, MI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

17 of 19 people found this instruction helpful.

Was this instruction helpful to you?

Dryer kept spinning when the door opened

Came to Parts Select. Looked for door switch. Read what other people did. Part came in a few days took a few minutes to take old switch out (had to pry the plastic connection apart with little thin screwdriver). Everything was easy

Parts Used:

Dryer Door Switch Assembly

Gary from Ocean Springs, MS
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

16 of 18 people found this instruction helpful.

Was this instruction helpful to you?

Drum would get hung up, belt would slip sometimes and there was a squeaking sound

Pull the front off. The belt was removed from idler pulley which was missing the wheel and pulled drum forward . Removed drum, replaced rear drum support roller kit and idler pulley assembly, put belt on and slid drum back in. Installed front panel, plugged in, works like a new dryer. It was very simple.

Parts Used:

Dryer Idler Pulley Assembly

Rear Drum Support Roller Kit

Multi Rib Belt - 92-1/4"

Lint Filter

Michael from N CHESTERFLD, VA
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers

18 of 24 people found this instruction helpful.

Was this instruction helpful to you?

Door catch on dryer door broke

PartSelect sent me three different door catches with instructions for choosing the correct one. I did choose and simply inserted it into the slot and voile! All finished and it works great now! PartSelect had the part delivered the day after my order was placed. I would suggest doing business with them to anyone asking who they might contact for a part. I especially appreciated the ease of identifying and ordering from them. I was able to do all of this on-line via their website.

Parts Used:

Door Catch Kit

Lynne from Jamestown, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

14 of 14 people found this instruction helpful.

Was this instruction helpful to you?

Loud banging noise when running dryer

Found one of the two drum support rollers was badly worn. Found Partselect.com, found my parts in less then 2 mins. Figured that I was in there so I should just replace the belt so I got one of those also. Parts arrived in 3 days dryer as good as new in 20 mins.

Parts Used:

Rear Drum Support Roller Kit

Multi Rib Belt - 92-1/4"

Joseph from Prospect Park, PA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers

15 of 18 people found this instruction helpful.

Was this instruction helpful to you?

Time clock not moving .Not enough heat

Opened front panel .Tested both coils on gas valve.
Found no continuity on one of the coils. Replaced coil,
dryer works like new.

Parts Used:

M Series New Style Coil Kit

PHILIP from LONG ISLAND CITY, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers

16 of 21 people found this instruction helpful.

Was this instruction helpful to you?

Dead motor

1. Shut off gas and disconnected dryer.
2. Opened cabinet. Easy sheet metal screws and fairly obvious how everything goes together. NB: You'll need a block (or a helper to hold things while you run to look for one) to hold the drum while removing the front.
3. The motor is connected with a single harness, so wiring is a snap.
4. Removing the blower wheel from the back was hard. I braced the motor shaft and turned with all the leverage I could muster, but it was stuck. Plan B: Recip saw to cut the shaft. Motor comes out one side and the fan comes out the other.
5. The fan, of course, was unusable because there was still a piece of motor shaft stuck in the thread. This is why I had to spring for a new wheel.
6. Put everything back together and receive wife's adoring praise...

Parts Used:

Dryer Blower wheel

Robert from Glencoe, IL
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Screw drivers, Socket set

17 of 24 people found this instruction helpful.

Was this instruction helpful to you?

Change dryer belt

I opened up the dryer as per the instructions I had received from PartSelect tech support. It was very easy to do. The only unexpected thing was that the original belt had snapped and in doing so the idler pulley was actually laying on the floor of the dryer's bottom. I had to figure out how it went, but that only took a minute and I popped it back into place. I held the drum by hand while pulling the dryer face away so it wouldn't fall and then I slipped the belt over the drum and quickly closed the front up again. I aligned the belt on the spot where the old one had been, pulled it through the idler pulley and over the motor and voila. Done. I closed up the dryer and was on to another "Honey Do" project within 20 minutes.

Parts Used:

Multi Rib Belt - 92-1/4"