Models > HTDX100EM5WW > Instructions

HTDX100EM5WW Hotpoint Dryer - Instructions

All Instructions for the HTDX100EM5WW
121 - 135 of 276
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Timer Knob
Very repair just put new on and it worked great
Parts Used:
Timer Knob
  • Sharon from FARMERVILLE, LA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replace knob
No brainer
Parts Used:
Timer Knob
  • Dave from DOUGLAS, WY
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The old dryer knob broke
I took off the old dryer knob and put on the new one
Parts Used:
Timer Knob
  • Charlie from KILGORE, TX
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door handle broke
Called my son-in-law. Easy as pie
Parts Used:
Door Handle - White
  • Cheryl from WILDER, KY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
My lint filter had a big hole in it. My dryer is 10+ years old.
All I had to do was remove the damaged filter and replace it with te new one. It could not ave been easier.
Parts Used:
Lint Filter - White Frame
  • JUDITH from FRUITA, CO
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Switch not working.
Open the door and removed the part. Installed the new part and started the dryer.
Parts Used:
Door Switch
  • Alan from BELFORD, NJ
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
BELT SQUEAKING
TOOK OFF TOP AND FRONT PANEL REACHED IN UNDER TUBE AND REMOVED FROM BELT TENSIONER HARDEST PART IS PUTTING BACK ON TENSIONER TAKES TWO HANDS LAYING ON YOUR BELLY
Parts Used:
Drive Belt
  • Al from CORP CHRISTI, TX
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
broken dryer door handle
removed remaining handle pieces and simply snapped the new part in place. very simple,very easy.
Parts Used:
Door Handle - White
  • Danny from DOVER, AR
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Old lint filter had deteriorated
Removed old one, inserted new one in slot. Just have to be sure it's turned in the right direction.
Parts Used:
Lint Filter - White Frame
  • Doug from INMAN, SC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer needed a new dryer belt
I followed the directions I found on my tablet on youtube.
Parts Used:
Drive Belt
  • Cindy from EPHRATA, PA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Pliers, Screw drivers, Wrench set
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
drive belt is broken.
Follow the instructions from YOUTUBE to replace the new drive belt..
Parts Used:
Drive Belt
  • Phuc from WOODBRIDGE, VA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Cracked air duct
Two screws under the dryer door then the top comes off.Then two screws hold the front on come out. 4 screws top is off and front is off the rest is no problem.
Parts Used:
Dryer Lint Chute Assembly
  • Forrest from Mays Landing, NJ
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Screw drivers
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
dryer belt snapped
Replaced it as one would. I took off the front facing and replaced the belt. It took a bit of searching to find the proper way to route the belt around the pulley.

It took a while since it was my first time and I wasn't sure what to take apart and what to leave intact.

If I were to do it again, it would take 30 minutes or less.
Parts Used:
Drive Belt
  • Michael from Laurel Springs, NJ
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Screw drivers
3 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Black marks showing up on garments.
Once I figured out how to remove the control panel. The rest was very easy. Upon pulling off the knob in the center of the control panel, there was a screw behind it. Once removed I used the palm of my hand and gave it a couple of upward hits in the center while the door was open. It slid up and I removed the electrical connections. Then carefully removed the top by pushing from the rear of the machine slightly and lifted off. Then removing the screws that hold the front on . After that it went pretty easily, reassembly went in reverse and. That was that!
Parts Used:
Dryer Bearing Slide (2 Pack) Dryer Bearing Slide (2 Pack) Duct Felt Seal
  • Garry from CONNELL, WA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Bad dryer motor
Replaced dryer motor which was a perfect fit thanks to your help. The process was helped by the internet videos available for the step by step procedure of taking the dryer apart and replacing the bad motor. I also was able to completely clean the inside of the dryer thoroughly, and reassemble it back together .
Parts Used:
Drive Motor and Pulley
  • Darryl from FARR WEST, UT
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Pliers, Screw drivers, Socket set, Wrench (Adjustable)
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the HTDX100EM5WW
121 - 135 of 276