GZS22IYNXHFS General Electric Refrigerator - Instructions

I located the light switch at the bottom of the area where the door closes. I just popped it out with a small screwdriver and installed the new switch. A 2 wire connecter and small clip is all there is to it.

I got the model # off the fridge, ordered the part online. The part was fairly cheap and was at my house 2 days after I ordered it. It was the exact part and I installed it in about 15 minutes and everyting worked out fine and easy and cheap, under $15 total to fix the issue. All I needed to do was use a flathead screwdriver to "pop" out the old switch, remove the 2 wires off the wire connection points, put the wires on the new switch and push it back into place. easy. Great place to get exact parts and fast shipping.

1. Removed light cover.
2. Removed old light assembly board from cable, (1 of 3 lights).
3. Connected cable to light assembly board.
4. Replace light cover.
5. All 3 lights fully lighted.
6. Installation Completed.

Take off all , then install.. following the version..

follow the easy instructions replace 3 temperature sensors cut the wires and crimp them with new sensor and it works like new

Simply remove the old dispenser and replace with the new one

My father called and asked me if I knew where he could get a new switch light for his refrigerator. I came across your web site and found the part right away. In less than 3 days the part came and my father put it on. He said it was easy and that it was great to have the part come to him instead of having to search all over town. Thanks so much for the fast, easy service.

I put kickplate on refrigerator and use 2 sheetrock screws and drill to attach. Done in 5 minutes.

FOLLOW INSTRUCTIONS OF YOUR VIDEO

Fridge and freezer were not keeping proper temp (freezer would get too cold, fridge too warm), as the cooling coils were icing over and needed manual defrosting; it was not going thru the automatic defrost cycle. Changed out the defrost heating element, thermostat, and two temp sensors, none of that worked. It was this part (main board) that was the culprit. Eight wire harnesses to undo and re-hook, one was hard to pull out but it came out. Read and follow the anti-static instructions. To make sure, I grounded my hand with a copper bracelet that was grounded with a copper wire to the metal chassis of the fridge. I also drew out a rough sketch of the connections and numbered them all with a black fine tipped felt marker before undoing them. This finally fixed the problem.

I watched the video online and it said there were three sensors in the refrigerator, two in the freezer and one in the refrigerator. I only ordered one sensor and was going to try the one in the refrigerator first. He said the upper one in the freezer is the most difficult, but is usually the problem. So, I replaced the upper sensor and tried restarting the unit. Everything went well and it fixed the problem.

After inspection of the new door recess assembly, I realized that I could use sidecutters (electronic assembly type) and 'clip' off the inward lock tabs of the old recess assembly and disengage it from the crank door arm without any further disassembly of the refrigerator door. It was easy to 'unhitch' the tang from the crank arm and wiggle it out through the external opening of the ice/water dispenser compartment. I reversed the process and inserted the new assembly through the external opening of the compartment. The new door recess assembly snapped into place on the crank arm and fit tightly against the ice chute opening, correcting the issue caused by aging distortion of the old rubber seal cup portion of the door recess assembly.

Changing out solenoid was very easy, but you don't have to remove trim ring and it didn't fix my problem. Turns out a relay fell out of its holder in the piece you have after removing the 4 screws per the video.

Went exactly by the video. Perfect job, you send the installation video with the part. You watch the video before or during, goof proof, took longer to disassemble than to replace the part.

my freezer quit freezing, it would freeze for one day, thaw the next, so I went online, found PARTS SELECT, LOOKED UP MY MODEL #, come to find out it needed three parts to keep my freezer to freeze, first part was a thermistor a small PART took me longer to remove all the covers, and shelving, PULLED THE OLD OUT, CUT THE WIERS TO SIZE, AND REINSTALLED, IT WELL! THAT WASN'T ENOUGH THE FREEZER STILL DIDN'T FREEZE IT THOUT IT WAS A COOL WORMING OVEN, HAD TO INSTALL THE THERMISTOR I, SO I DID, TEN MIN, NOW I THOUGHT THAT WAS IT BECAUSE IT STAYED FROZEN FOR A WEAK, HAVE YOU EVER EATEN SOUPY ICE CREAM? SO BACK TO PARTS SELECT, THIS TIME I BOUGHT ONE MORE PT, THE RUN CAPACITOR, FIVE MIN, THAT/S ALL IT TOOK TO INSTALL. I DID NOT KNOW AT THE TIME YOU NEED THE THREE OF THEM TO RUN THE FREEZER ONE TO KEEP THE TEMP., ONE TO KEEP THE FAN RUNNING THE WAY IT SHOULD, AND THE THIRD TO MAKE SURE THE OTHER TWO KEEP RUNNING. NOW I CAN SET IT AT 4- 5 AND. FREEZE.