All Installation Instructions for General Electric Washer GTWP1000M2WW

Would not pump out water

Wife put on the new part and she used a pair of plires and it was a little difficult to get her hand in the tiny spot but she put it on in less than 15 minuets and it is working great.

Parts Used:

Drain Pump and Motor Assembly

stephen from brooklyn, MI
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

tube would fill, but agitor would not ingage

replace lid switch

Parts Used:

Lid Switch with Wire Harness

Harm from JENISON, MI
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

tub moving allover the place

replaced broken straps all 4. washer not working ]. replaced lid switch with wire harness.replaced bad old belt.working fine now. my wife is very happy. thanks for your videos and how to do the job right.

Parts Used:

Lid Switch with Wire Harness

6-Rib Drive Belt

DAMPENING STRAP 2PACK

GABRIEL from LA QUINTA, CA
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

My washer started leaking water out of the bottom.

I pushed a small screwdriver under the top lid and pulled the front out and lifted it out or the way. The rubber hose had two clamps holding it. One you loosen with a flat screwdriver and the other one you squeeze with pliers to remove hose.Then replace hose and put front back on. It's very simple.

Parts Used:

Pump to Tub Inlet Drain Hose

Wallace from Delbarton, WV
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

hammering on the tub nut wrench rotated the drive axle & pulley

I had to insert a broom stick to keep the drive pulley from rotating as I hammered the tub nut loose.

2nd tip, my washer has the standard agitator with the glued on cap; it was unclear if I needed to remove it; you should clarify that this is not necessary, that one must only pop up the entire agitator; I used a shipping strap looped under the agitator and over a 2x4 across the top of the frame, tightening until the tub was raised a bit and then a gentle pop down on the tub and the agitator easily popped off.

Parts Used:

Tub Bearing

Martin from LAKE ST LOUIS, MO
Difficulty Level:
Difficult
Total Repair Time:
More than 2 hours
Tools:
Nutdriver, Pliers, Screw drivers, Socket set

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Noisy on spin, leaking water

Could not complete repair. The pulsator was rusted on the shaft, used wd 40, finally pried off the shaft. The hub nut was so corroded on the shaft I could not remove it. Reassembled the Machine.

Parts Used:

Tub Seal

Tub Bearing

Tub Bearing Washer

Robert from WOBURN, MA
Difficulty Level:
Very Difficult
Total Repair Time:
More than 2 hours
Tools:
Pliers, Screw drivers, Socket set, Wrench (Adjustable)

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Drain hose was leaking

Surprisingly easy. I took the screws off, then pulled off the drain hose. I then inserted the new hose, and put back the screws. Amazing quick!

Parts Used:

Drain Hose

Mohammed from Berkeley, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Indicator dial broken

The dial is held on the cycle control shaft w/a clip. Using a small pair of long nose pliers, pull the clip out of the slot in the control knob. Remove the outer knob exposing the indicator.Easy....

Parts Used:

Dial with Compression Ring

Reginald from ROCKLEDGE, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Small wire had tried spin out of drain pump. Wore pin hole in the rubber drain hose....

Unplugged...Removed back from washer...Using nut driver-cordless drill...Inspected hose-found leak....Removed hose with pliers & screw driver.....Than dried the hose...& than for temporary fix (for the wife to continue washing) used some Epoxy for rubber.....Than ordered new part. Received and reinstalled replacement. Thank you

Parts Used:

Pump to Tub Inlet Drain Hose

Steven from PLAINS, MT
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Straps had stretched with age.

Removed the front panel. Removed the washer top. Removed and replaced each strap. Very simple repair.

Parts Used:

DAMPENING STRAP 2PACK

Roger from Longmont, CO
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Screw drivers, Socket set

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Debris in pump

Could have removed debis in old pump. Kept it as a spare.
Replacement was simple , (two nuts) & (2 Lg. Hose Clamps) + two wires.
Dealer wanted $168.00 Labor + $67.00 for part!.

Parts Used:

Drain Pump and Motor Assembly

Howard from Davie, FL
Difficulty Level:
A Bit Difficult
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Socket set

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Water Kept Flowing into the tank even when water should have shut off.

The replacement of this tripe water valve was so easy. My tub kept filling with water even though the water should have shut of. First remove the two hoses from the valve. Second you remove the 3 screws from the steel shield behind the plastic upper control pan panel. Take the shield off. Remove the control panel and lay on the washer. Then take the filler hose to the tub off using pliers to remove the hose clamp. Then take the two screws out of the valve. Twist and remove the valve. That is the removal. Reverse all of these to put it back on and test out. This valve fixed my problem. Anyone can do this who has any basic knowledge of tools.

Parts Used:

Triple Water Valve

William from W BROOKFIELD, MA
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers, Socket set

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Fitted sheet got stuck under the agitator

Reach down and grab the base of the agitator with both hands and yank up with slightly more pressure on the left or right, whichever side you prefer. This will break loose the holding clamps/pull straight up. To re-install: align slots and push down until it snaps. Simple as that.

Parts Used:

Dual Action Agitator

Donn from WIMAUMA, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

selector knob plastic teeth mostly gone, difficult to select wash cycle

Unplug washer to keep from running.Pull out on selector. After determining how knob was held in place, used coat hanger with short 90 on one end to catch clip holding knob in place. Pulled clip, removed knob.Placed clip on back of new knob just enough to hold. Placed knob on shaft, pressed down on clip to lock in place. All Done. Use of small flashlight is helpful. Replug washer.

Parts Used: