GTW680BSJ2WS General Electric Washer - Instructions

Took off belt/motor housing and replaced belt. Put housing back on. Very easy.

Dipped water out as much as possible,tited washer at a 45 degree angle and propped it up. Took the 3 bolts out holding the pump assembly and the 3 bolts holding the belt guard.Unplug wire connecter,pull out assembly and than pull drain hose off of assembly. Reinstall the same as you take apart. Was a easy fix, and worked as it should.

This was a very easy repair. It is basically and 'plug & play'. Be sure to separate the panel from the silver back plate slowly and carefully and note all connections, particularly the orange hollow tube connection. Every connector can only go into one corresponding spot. The most time spent was removing the screws to get inside the housing.

Removed the center agitator to clean it - had black mold and pink soap scum buildup underneath that you couldn't see or clean without taking it apart. Removed the bolt with ease. Upon tightening the bolt back in place, the bolt sheared in half, leaving the lower half threaded in place and the head in the socket. Had to use a drill bit and drill out the lower half of the bolt completely. Ordered the replacement bolt and reassembled everything in less than 5 minutes. Replacement part was perfect - hopefully it lasts longer than the original bolt.

I contacted parts select and entered washer information and asked them if they thought they would now what the problem was and and they responded with a answer and also a list of two parts that they thought might take care of the problem. I ordered the parts,looked on u tube to see how to change them and replaced both parts .I think the clutch was good but the drive belt was stretched and needed replaced.Know it works great.

We disconnected the rear of the dashboard and folded it toward. We unsnapped the top cover and exposed the lid lock. We removed the old lid lock and replaced it with the new parts from SelectPart. Put it all back together.

unplugged old part plugged in new, took about 2 minutes.

this is a great web site, I didn't have to wait for a serviceman to come. and maybe not have the part and come back again. ........thanks

Unplugged washer and hoses. Removed 4 screws in back control panel and 4 screws holding control panel down. Drained capacitor and checked that. It was good. Pryed washer top off with screw driver. Used vice grips to remove old and install new spring rods, replacing them one at a time. While lid was off I cut a small diameter pool noodle in half and cut 4 half noodles the size of each side. I unclipped one side of the tub cap and ran an 11" zip tie through the hole in the middle of one side and back up and out where the tub skirt and cap meet, then tied the half noodle to the edge of the tub cap and snapped down cap. Then repeated with the other three sides. I did this so heavier clothes, if they got out of balance, would continue to spin. The noodles keeping the tub from moving too far out of balance. The rod springs helped with lighter loads but still shut down spinning with heavy clothes. The machine always handled heavy clothes for 7 years until the last month or so. If it breaks with the noodles, I'll get another new machine.

Extremely easy. You will need a helper to make it easy. The best directions are on you tube.

Unplug washer; turn off hot/cold water valves at wall. Access rear of washer; remove 2 long screws anchoring control panel; remove 3 short screws along top of control panel; remove panel; rotate panel forward to rest on washer top (disconnect orange pressure attached to green computer panel. Blue water valve assembly is obvious! Remove hot & cold inlet hoses from washer (have bucket handy to catch water in hoses). Take picture of old water valve so you can reinstall electrical clips in exact same sequence! Remove 3 short screws that anchor water valve; lift out water valve; disconnect clips; gently life out old water valve. Install new water valve in reverse order.

Use needle-nose pliers as a lever to remove tight electrical clips (they are not designed to come loose easily). Google online videos. Really easy, when you watch a couple videos!

I just took old one out an put new one in

You have to take the top off of the washer and the four suspension rods are at each corner. Fairly simple removal and installation of the rods. A quick you tube search is all it took. Easy peasy.

The drain pump had three screws. Frist unplug the machine and turn the water off. And unplug the hose for the Hot and Clod Water. Make sure their no water in the tub. Unplug the pipe from the Tub. The unscrew the nut for the connector. Then unplug the connector and be careful not to damage plug for the connector. Press the plug connector with your finger or long nose pliers . Then just hook the new plumb and you all set.

REALLY easy-
Just unscrewed the two screws with a Phillips, slid the old one out, the new one set in perfectly, and used the same screws to hold it in place. 2 minute task total.

Put the parts in, turned washer on.....lid lock still blinks, will not operate. Suggest the control board that sends the signal to the solenoid lid lock switch is defective. Buying a new washer, scrapping this one.