GTL22JCP General Electric Refrigerator - Instructions

Followed the video you posted on your website and it went seamlessly.
Removed the full unit and after replacing the motor - placed back in slot, secured and ran perfectly.
Hot center bar no longer a problem

my freezer quit freezing, it would freeze for one day, thaw the next, so I went online, found PARTS SELECT, LOOKED UP MY MODEL #, come to find out it needed three parts to keep my freezer to freeze, first part was a thermistor a small PART took me longer to remove all the covers, and shelving, PULLED THE OLD OUT, CUT THE WIERS TO SIZE, AND REINSTALLED, IT WELL! THAT WASN'T ENOUGH THE FREEZER STILL DIDN'T FREEZE IT THOUT IT WAS A COOL WORMING OVEN, HAD TO INSTALL THE THERMISTOR I, SO I DID, TEN MIN, NOW I THOUGHT THAT WAS IT BECAUSE IT STAYED FROZEN FOR A WEAK, HAVE YOU EVER EATEN SOUPY ICE CREAM? SO BACK TO PARTS SELECT, THIS TIME I BOUGHT ONE MORE PT, THE RUN CAPACITOR, FIVE MIN, THAT/S ALL IT TOOK TO INSTALL. I DID NOT KNOW AT THE TIME YOU NEED THE THREE OF THEM TO RUN THE FREEZER ONE TO KEEP THE TEMP., ONE TO KEEP THE FAN RUNNING THE WAY IT SHOULD, AND THE THIRD TO MAKE SURE THE OTHER TWO KEEP RUNNING. NOW I CAN SET IT AT 4- 5 AND. FREEZE.

0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.

I was astonished when my part (PS306943 SLIDE ASM LH (Drawer Slide Rail - left side)arrived the very next day!!
In a big box, beautifully wrapped.
I got out my screw driver, detached the dead shelf support and screwed in the new one.
Oh it's so very nice to have the fridge working again, and so soon.
Hooray for Part select.com
The best thing since sliced bread.
Jill

It just unpluged and the new one plugged in. Simple. The part was reasonable and arrived very quickly. It sure is nice to have a light in the frig again.

replaced lights in refrigirator and freezer

all i did was follow the video.

absolutely flawless tutorial.

the video is on the website.

Installation could not have been easier!

Installing the part repaired the fridge and freezer immediately.

Did the repair just as the instruction said, once I read it. The part I didn't read was that if the plug was under the ice maker, you had to take the wire out of the clip on the side. So, had to dismount ice maker, unclip wire, remount maker, plug it in. Still under 30 minutes. Thank you.

I followed the instructions from the repair video that was posted in the part description. It was exactly the same as shown in the video.

got on part select web site and found other customers that had same problem and on their site they had comments from them to fix problem. I then took off back panel on frig where compressor is by removing 6 screws and found the relay attached to the compressor then pressing down on holding spring removed 2 wire alligator clips and it was bad ordered one from part select put the new one on an frig was fixed. entire fix took about 30 minutes from isolating problem to fixing it. thank you part select

I followed the instructions provided on the video emailed to me. I had some trouble only because my refrigerator was slightly different and it was hard to get the old condenser fan motor out. Other than that I was super pleased to have found Partselect.com. There is no way I would have been able to tackle such a major job without their step-by-step detailed help. I am enormously grateful to them. They shipped my parts the next day which is evidence of their sincere concern and understanding of the urgency of my problem. I can surely say they saved me many hundreds of dollars!

I made my wife fix it.

Checked water inlet tube inside freezer, stuck screwdriver in it to see if there was any ice and it seemed clear. Checked water pressure to fill valve, good pressure. Replaced fill valve, still no water to ice maker. Replaced Ice Maker. Still no water to Ice Maker. Removed freezer back panel, hit fill tube with heat gun after allowing freezer to defrost awhile, replaced back panel, ice maker. Water going to icemaker fine. Problem was that the fill tube was frozen up way at the back where the water line emptys into the icemaker fill tube. Old icemaker and fill valve were probably OK. No real way to check it from outside the case in the rear of the fridge as the water line is sealed on the fill tube and heating it without removing the rear freezer panel does not get back far enough to melt the ice.