GTL22JBPDRBS General Electric Refrigerator - Instructions

Remove entire shelf from refrigerator and removed broke, set the replacement part in place, screwed it in and it worked perfectly, done infive minutes. Took me longer to take out the self that to do the replacement.

Went to Sears, where I bought the Fridge, they could not locate the part I needed, so I went on line, and found partselect.com, entered the proper information, found the part I needed fast, ordered the part, received it in two days time, I already had the old part off, so it took less than ten minutes to replace it with the new part, works great, the people at partselect.com were great, an if needed, I will gladly order from them again.

My snack tray guide rail cracked and this was the easiest repair I've ever made.

Follow the instructions on the video. Took pictures removing Evaporator Fan Motor. Installed new motor in 44 minutes. Thank you part Slect

unplug fridge! removed ice maker. removed the back panel in frezer. I uncliped thermostat; cut wires on thermostat and installed new thermostat.

On partselects video the gentleman removes the fan and housing in one piece. This is a great idea but does not work on this brand of ge. I removed the fan housing screw as instructed but left it in place and swiveled it enough to access the retaining screws with a socket driver. Over all swap of the fan was seamless and the video is a gem. Andy

Replaced above parts and the noise problem was not resolved. Ordered a new motor, fan blade and another set of grommets from PartSelect. The parts were delivered the next day. Took me about 15 minutes to swap the new parts in. It's been 3 days since the repair and the noise has not returned.

Follow the directions on the video, removed the back panel, unplugged the existing fan, removed the fan assembly, installed the new motor and reassembled the components.

took screw that holds motor frame in place out with nutdriver, rolled motor frame out after unplugging motor,took screw out of strap that held motor in frame, removed bushings from old motor and put them on the new one and re3versed the proceedure.

Just follow the instructions from the Youtube, the link to the video is included in the sheet coming with the part. It was easy to take the entire compartment out as instructed, however, after replace the old motor with the new one, it took more than 20 min to put the entire compartment back after trying different ways. It has been working greatly since it was repaired.

Not knowing anything about a refrigerator it was hard to find the source of the noise. Once I could isolate it we googled the appliance repair and found the video from Parts Select and the rest was a piece of cake. Saved a service call and bloated parts prices. Thank you Parts Select!!!

Empty the contents of the freezer.Take out the one shelf.Remove the plastic pieces covering the fan and evaporator removing 2 screws with the nut driver.Remove the metal back using the nut driver(2 screws)Remove the fan assembly from the back of the freezer.(4 screws)Remove the green ground wire from the fan assembly(1 screw) Take the fan assembly out of the freezer and remove the old fan(2 screws) and reinstall the new fan.Assemble the parts in the reverse order .Very simple and intuitive for anyone who is "handy" at all.

condenser fan on bottom condenser not runningchanged fan and fan motor

I removed the ice maker, and removed the upper plastic covers, that just snap in and out of their locations, you can then see the evaporator fan blades. then I removed 2 hex screws, located in the top corners, holding a metal cover in place,lifting up from the bottom of the cover and slowly pulling it out of the freezer compartment. I can now see the screws holding the evaporator fan motor in place. Unplug the connector wiring to the motor and unclip the ground wire from the frame, It is easier to replace the fan blade,lid bumpers, dust cap,grommets, and fan motor this way. while you have everything in easy access, I took time to clean everything and replaced the foam strips, assure tight fit causing excellent air flow, when operating. the cause of the whining and knocking noise, was worn out grommets and bearing going bad in the motor. I reassembled everything in reverse order, being very careful not to get cut or burnt on the fins and tubing in the back of the freezer. Do not drop any thing down the drains while removing and /or reassembling, those items will cause lots of havoc to the lower fan and motor for the refrigerator, lay a towel in the bottom when you start working on it.. I then plugged it back up and there was on noise, works great.

I removed the ice marker first and took the back panel off using a nut driver. Be careful I had wires tied to the back panel, so I moved it like opening a door, right to left. The I removed the fan motor. Be careful not to damage the fan blades. I took the fan blades off and the dust cover. The dust cover was very tight. I had to use a very small screw driver to get it off. When I put the dust cover on the new motor I did not push it down tight. I turned the spindle of the new motor to make sure it turned. The put everything back. Turned it on and it worked. I put the ice marker on last. Take a note of how far the fan blades are on the spindle. The refrigerator now turns off more often.