GSC412--65 General Electric Dishwasher - Instructions

After doing dishes by hand for four months, I decided to take a look at the dishwasher. It took about 40 minutes to identify the problem and order the part fom PartSelect. The part arrived in two days and took two minutes to install. It's best not to rush into these things.

I took the dishwasher out from under the sink and looked at the pump and motor, saw that the cooling fan that this old style motor used was broke. Ordered this kit and installed it. I didn't even look at the directions that simple of a swap. Thank God!

Instead of purchasing a new dishwasher, I elected to replace the motor/pump assembly which the existing was noisy and leaking water. To start to took pictures of the existing assembly and marked the wiring connections. I read the instructions a few times until I fully understood and had the necessary parts identified. The only problem was the bracket that holds the solenoid has two holes for mounting the drain feedback bracket were not threaded. I was able to tap the holes (metric) and mount the bracket. Caution must taken not damage the solenoid coil.

This was a 45 min project. New pump was a redesign. Match your style with the instruction sheet. ( pictures are upside down) Install drain on pump. Remove wirng connectors(3) and hanger. Raemove in/out pump clamps, and remove pump. Reverse procedure( I had to bend the new hanger to fit). When I first fired it up, nothing happened for about 5 min. Then water got into the pump and it started working. Quieter, more powerful spray. Grabbed a beer.

The motor/pump Kit I purchased could fix/be installed in any GE dishwasher made since 1970. I would guess that the one I have is about 15-20 years old. I encountered only one small problem with the kit------ a motor hanger that had to be bent a bit to fit correctly. Other than that it was a total breeze. The clear instructions included in the kit helped quite a bit. In 30 minutes or so ,I was done and our machine was back in operation

Dishwasher is 22 years old and I'm 80 years old so it took longer, about 3 hours. After removing, turned upside down and removed old pump-motor assembly and replaced with new following directions [which took a little while to figure out; my assembly was quite a bit different from the replacement pump-motor]. Pleasantly surprised at how quiet the dishwasher now runs. Normally I would replace this old an appliance, but this unit has provision for inserting a wood panel that blends with the cabinets and a new GE dishwasher with this feature costs $1300 MSRP. I'm trying to save money for when I get old so I decided to do the repair myself. For $150 it was a worthwhile investment.

There is sufficient clearance to remove the motor and pump from under the dishwasher after removal of the front lower panels. This avoids the inconvenience of moving the dishwasher. Some ouch work required to remove some of the fittings as sight lines are obstructed - use a mirror to help. Installation is easier as all but one of the hose and pump clamps can be installed with the screw heads accessible from the front. Only installation issue was that the mounting holes on the pump body for the ground wires and the support piece had been drilled but no screw threads had been cut. Two minutes work with a tap solved the problem. One suggestion is to run a couple of loads before replacing the front cover to check for leaks. I did find one after the second load.

Removed and inverted the DW. Removed the impeller, grinder, screen and seals then the actual shaft seal. Replaced with new parts in reverse order. Instructions provided with the seal kit were simple and excellent. They were right to the point.

Followed the enclosed directions and the video helped a lot. My model needed a different motor mount bar than in the video but wasn't hard to figure out. From shutoff of the water, unplugging, and undoing the screws under the counter and pulling the old pump/motor and installing the new pump/motor and putting it all back took a leisurely 90 minutes. Be sure to hang onto the old plastic covers for the electric leads to reuse.

Most difficult part of repair was getting dishwasher out and in under the cabinet. Especially, feeding the copper water line from under the sink and then back while trying to align the connection. Installing the part itself was easy with good instruction for taking it off and reinstalling. However, since the motor had been upgraded, it required new connections. The connections were provided for this, but no instructions for the electrical connections.

Too easy- what made it easier was this is a portable roll-around unit I could lay on it's back. Loosen the two clamps around the washer pump, hook up the drain solenoid, washer motor wires, attach the motor hanger, that's basically it. It took longer to make sure I was working from the right set of instructions- this pump covers several models. Once I had that right, it was really a snap. Now the unit is so quiet. It once sounded like a jet engine in the kitchen, now it runs so quiet you can hear the water splashing around inside- a big improvement. We should be able to hang onto this thing for a while longer.

At first, I found a metal band that was rusted and loose, replaced it but still had a leak. I went to the diagnosis section and identified another area of problem, ordered the part and got super quick delivery. With the help my wife I was able to pull apart, repair and get the unit to run and stay dry. Wife is happy because she loves the décor of our old but now dry dishwasher.

The repair went really smoothly, I found a video on youtube for how to remove the dishwasher, and the video on the parts page did a great job covering replacing the motor. The repair went really well. As others have noted, it ran really nosily the 1st time, and a little the 2nd. After that, it ran quieter, and stronger than it has in the 4 years we have owned the house.

I had some extra problems with my water supply line since this is an old house, but I won't dwell on that. If you have an older model like mine (probably 80's) the only trick is with the drain solenoid. The kit uses a newer style solenoid that is a little different. Without getting too technical here, let me just say that if the old solenoid has a little metal lever that is actuated when the plunger goes down do not discard it. From what I have read, the dishwasher will shut down with an error code if you don't use this part and you will also have 2 wires that are just hanging there with nothing to plug in to. You will need to use an included metal plate and screws to adapt that part to the new assembly. It takes a little mechanical aptitude, but after you figure it out it works perfectly. I did not see this mentioned in the instructions but the necessary parts were included. Replacing the pump and motor was fairly simple, and all the needed parts were included in the kit. I did remove the unit from under the counter and lay it on it's back for easy access to the pump and motor. It helps to watch some You-tube videos if you are unsure about how to do this, but make sure they are working on the brand you have. All dishwashers are NOT the same.

Turn off the power at the breaker panel. Turn off the water supply that goes to the dishwasher. Remove the front lower panel to gain access to disconnect the water line and electric. Now remove the two screws that connect the dishwasher to the countertop. You should be free to slide the dishwasher from under the countertop far enough to remove the drain hose. Slide the dishwasher out all the way and lay on the floor door down. Loosen the two clamps that hold the motor up. Remove the motor bracket, (should only be one screw. Disconnect the wires from the motor. Now just pull the motor down and out. Repeat the process to install the new motor. I took several pictures before I started removing anything. The instruction that comes with the kit is very good. Their will be parts in the kit that will not be used. Not to worry!