GS470LEMB4 Whirlpool Range - Instructions

Clean off all broken glass and wipe down the debree,figure what side the glass goes then unscewed the base then the sides then add gorrilla glue on the edges to help set the glass in place had some hold it the screw th center bottom in first then got the sides in place with the bottom rack then screw it all back in to place making sure the side and top were in place right that was it.

We took the door off and took it and the side panels to the local dealer and he put them on for us - for anyone needing to replace the side panels on the over, be aware they slide under the glass front -not over it like we tried to do. We thought, though, that we were going to have a buy a new stove but for a little over $70. 00 We got the parts, had them installed and saved over $800 on a new stove - well worth the effort.

Removed door per instructions in manual. Removed racks and storage drawer per manual. Removed two phillips head screws holding bottom pan and removed pan. Removed two phillips head screws holding igniter tube (#12) and withdrew tube from the cavity. Removed two phillips head screws holding igniter and bracket to the tube. Unplugged elcetrical connection to igniter and installed new igniter in reverse order. Too bad the igniter wasn't the problem.

The first thing you need to do is remove the racks from your oven.

Then look around at the back of your oven for the screws that hold the bottom pan down.

Remove those screws and remove the pan. Some need to slide back and then come up others will just pull up.

Remove the heat shield that is over the burner.

Remove the bottom drawer of your oven.

Now you should be able to see the igniter that sits on an angle by the burner tubes with a couple of wires coming out of it.

Removing the screws that hold the igniter is probably the most difficult part with some ovens. Sometimes it is easier to remove the whole bracket that holds the igniter and then remove and replace the igniter out of the oven.

The wires for the igniter will go to a Molex plug. Follow the wires and undo the plug. On many units it will be below the oven in the drawer opening at the top back. You will need to lay flat on the floor and reach back in to do this.

Once you have the old igniter out then you can carefully install the new one.

Check to make sure that you can feed the Molex plug and wires down through to the bottom before fastening the igniter.

Once the igniter is secured and the plug is connected, you can then replace the other parts in the reverse order that they came out.

I had to use a dremel to grind the heads off the rusted in screws that hold the burners to the stove top then drill out the screws and use larger sheet metal screws to reassemble. Don't lift the stove top much with the burners attached or you'll bend the gas lines. Two screws inside the top oven hold the top down. Without the rusted screws it would be an easy job.

This is a built-in oven, so the biggest problem was figuring out how to remove it from the cabinet. The solution turned out to be removing the cooktop above it and unscrewing two screws that connected the oven to the inside of the cabinet. The other problem was removing BOTH metal backs from the oven. The first one was easy. The second one wasn't. The old socket was recessed behind the second back, making it virtually impossible to access the metal "wings" that hold it in place, so I ended up pulling out the socket assembly from inside the oven with pliers.

Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.

Using 4 strips of duct tape was useful,in holding the glass to the door.

Take off the back panel of stove and unplugged timer motor and switch on door latch assembly,removed two screws that hold assembly and slide rod off. I put 110 volt plug to timer motor and it did not move, that is how I diagnosed problem. Ordered new assembly (cannot buy just timer motor)put new door latch assembly on and worked fine. Of course unplug stove before you start !

take the 2 screws that hold the handle on out...watch the glass front and the side trims because the handle holds them on. Take the glass out then remove the side trims. Replace the side trims holding the glass in place with 2 pieces of masking tape om each side then install the handle with the 2 screws and remove the masking tape.

I removed the handle from the door, replaced the old one with the new one............. 1, 2, 3, just that easy. The replacement part arrived very quickly and the price could not be beat. Would I use them again...........Yes!

I had to bring the new handle to the Hardware store and have them pick out screws that would work. The only problem is that I live 12 miles one way from the Hardware store. My advise is to order scews when ordering the handle.

The bake part of the oven was not igniting all the time . I checked the website and they don't list the igniter separately from the burner tube. This part is the exact fit for the igniter. There is no need to buy the whole kit if the igniter is all you need. it will fit right on the burner tube with no modification at all. Part number PS897264 is the igniter and burner tube. Part number PS898618 is just the ignitor.

Looked up on-line the error problem and what part I needed to fix it. Part arrived very quickly and everything was going fine until I realized the stove had two sensors. Replaced the top sensor now I am getting an error on the bottom sensor. Maybe I replaced the wrong one. I will replace the bottom sensor with the one I took out and see if that does the trick. Very very satisfied with PartsSelect. Good Price, Quick Shipping, Would do business with them again. They are now in my favorites so I can find them again if I need parts.

So, after several years of it bothering me, I decided to replace the oven panel. I ordered it one day and it arrived the very next day. It was an easy job to replace. Just remove two screws in back and replace the panel. While I was at it I also replaced the racks. Now I have a brand new oven,thanks to PartsSelect!