GS2928EEDW Maytag Refrigerator - Instructions

Removed the top hinge of the door. Lift door off the lower hinge. Unscrewed the "natural closer" from the bottom of the door and replaced with new part. Pulled off the lower hinge from the lower bracket and replaced with new hinge pin. Replaced and realigned door. Piece of cake!

Went to PartsSelect. Put in Dishwasher model number. Chose the screws for that model number. Ordered the screws. Can't get any easier than that!

Place two 2x4s, stacked on each other on floor parallel and close to refrigerator, leaving room for socket handle and extensions to three lower hinge bolts. Placed 3 foot 2x4 at right angles on top of the parallel stack of 2x4s, with one end under right hand refrigerator door. Placed 20-30 lb bucket of rice on other end of 2x4 to exert upward pressure on door, raising door bottom off of hinge pin. Removed three hinge screws. Replaced Natural Door Closer and Lower Hinge pin. Screwed three hinge pin screws back in. Removed fulcrum.

Pried out ice blade bar and removed broken water fill cup and replaced with new one.The whole repair costs $9.52 So I saved $ 190 over the cost of Appliance man visit!
It would have been $150& $50 for visit to replace ice maker unit.

The most time-consuming part was removing the screws. First, remove the 8 screws that attaches the ice bin to the front cover. This will free up the auger enough to pull up the back end where the drive ring is held in place. The ring just pops right out. The only thing I recommend is as long as you have the bin out (and empty), go ahead and give it a good wash. Make sure it is thoroughly dry so that no ice freezes to the moving parts.

1. mark location of removable baskets in door and remove baskets
2. remove three screws in top hinge - save shim under hinge
3. lift door from lower hinge
4. remove 3 screws from lower hinge bracket and remove bracket
5. install lower hinge bracket with 3 mounting screws
6. install lower hinge pin in bracket
7. clean upper and lower hinge holes in door
8. lubricate upper and lower hinge pins with grease
9. place door over lower hinge pin - the magnetic seals will hold it in place
10. install upper hinge bracket with 3 screws
11. install baskets in door

Note: The plastic piece on the bottom of the door that mates with the hinge pin and provides a cam action should have been replaced at the same time.

I read what other people had done so I tried the easiest solution--Forced, without breaking, the plastic & fit the ring right where it needed to be.

Replaced actuator pad

I simply removed the old brackets and replaced with the new ones. Can't get any easier than that!

Removed the food out of the fresh food door. Removed the top hinge cover, removed the 3 nut screws on top. Lifted the door off of the bottom pin. Set the door to one side. Removed the lower hinge pin with a screw driver and replaced with new product. Lifted door back onto lower hinge pin, secured the top pin hinge with the 3 nut screws, replaced the top hinge cover and placed food back into the door. Done in less than 15 minutes.

First, I removed the water/ice fountain panel - remove the 4 screws and disconnect the panel buttons cable. Second, I removed the panel circuit board - remove the two screws and disconnect the two wire connectors. Third, I pulled the water/ice fountain compartment. Removed the broken rubber pad (actuator pad), and installed the new one -- no tools needed for this step. Finally, I put everything back together. TIP: If the water/ice switch gets stuck, even with the new actuator, find a spring that can fit the switch pin that comes with the actuator. I had that problem, and I simply added a small spring.)

Most of the time was sent to removing and replacing door shelves. Pry off upper hinge cover. Easy, it's only plastic. Remove 3 fastener from top hinge and remove hinge. Lift door off lower hinge. Lay door down on table let handle hang over edge. Remove door closer attach fastener. Remove and replace door closer. Pry lower hinge up and out. Tap new lower hing pin into place. Replace door, upper hinge and hinge cover. Had to replace Door Closer and Hing Pin together; both were worn and needed replacing.

My husband did the replacement of the filter, so it was really easy for me. Easy for him too! The best part was this company had the best price, and the part was here in no time!

replaced the broken basket stop with new one. took a whole minute to do so!!!!!

This was easy. Removed the plastic cover at the top hinge. Removed the 3 screws at the top hinge. Lifted the door off of the bottom hinge and laid it on it's side. The part that was worn out is the "natural door closer". It looks like this part will need to be replaced every few years, it is made of plastic and was ground down to nubs. Remove the screws holding it down and replace it with the new one. Lubed it up with some WD40 to get rid of squeaks. I also replaced the lower hinge pin, but I don't think that was necessary.