GS2728EEDB Maytag Refrigerator - Instructions

Went to PartsSelect. Put in Dishwasher model number. Chose the screws for that model number. Ordered the screws. Can't get any easier than that!

have always done it myself, but Maytag store closed, so I didn't know where to purchase filter

I received it from Parts Select, in 2 days and if I remember right, price was cheaper than I paid last year, at store.

The most time-consuming part was removing the screws. First, remove the 8 screws that attaches the ice bin to the front cover. This will free up the auger enough to pull up the back end where the drive ring is held in place. The ring just pops right out. The only thing I recommend is as long as you have the bin out (and empty), go ahead and give it a good wash. Make sure it is thoroughly dry so that no ice freezes to the moving parts.

Most of the time was sent to removing and replacing door shelves. Pry off upper hinge cover. Easy, it's only plastic. Remove 3 fastener from top hinge and remove hinge. Lift door off lower hinge. Lay door down on table let handle hang over edge. Remove door closer attach fastener. Remove and replace door closer. Pry lower hinge up and out. Tap new lower hing pin into place. Replace door, upper hinge and hinge cover. Had to replace Door Closer and Hing Pin together; both were worn and needed replacing.

Since the old one kept falling off the disassembly was very easy. I lined up the five prongs on the new cover with the holes on the unit and snapped it into place. Job done,

Removed the food out of the fresh food door. Removed the top hinge cover, removed the 3 nut screws on top. Lifted the door off of the bottom pin. Set the door to one side. Removed the lower hinge pin with a screw driver and replaced with new product. Lifted door back onto lower hinge pin, secured the top pin hinge with the 3 nut screws, replaced the top hinge cover and placed food back into the door. Done in less than 15 minutes.

I simply removed the old brackets and replaced with the new ones. Can't get any easier than that!

My husband did the replacement of the filter, so it was really easy for me. Easy for him too! The best part was this company had the best price, and the part was here in no time!

This was easy. Removed the plastic cover at the top hinge. Removed the 3 screws at the top hinge. Lifted the door off of the bottom hinge and laid it on it's side. The part that was worn out is the "natural door closer". It looks like this part will need to be replaced every few years, it is made of plastic and was ground down to nubs. Remove the screws holding it down and replace it with the new one. Lubed it up with some WD40 to get rid of squeaks. I also replaced the lower hinge pin, but I don't think that was necessary.

replaced the broken basket stop with new one. took a whole minute to do so!!!!!

Open refridgerator door, remove old filter by hand in a counterclockwise direction. Insert new filter turning clockwise. Close refridgerator door and fill a glass with water from dispenser. This will remove air and ensure water to free flow. Check for leaks.

Just a filter replacement -- however more impressed with the speed of which I could receive the replacement.

Can't find them anywhere local -- glad I found Part Perfect!

Removed old filter with a twist and installed new filter the same way. Very simple task.

Used screw driver to pop out old switch. Used pliers to hold wire connection from fall back into slot on fridge. Inserted new swith into plug and pressed new switch back in place.

First we ordered a new solenoid. . . The little piece that opens and closes whenever you push the button to dispense ice. That definitely needed to be replaced, and it was easy to do. However, that didn't fix the problem, so we looked and looked at the assembly and decided that a spring was missing. We ordered the spring, and when it arrived, we found that it matched exactly one that was already on the assembly. :-) Not the problem. Thirty minutes later we figured it out,. The diagrams at part select were not helpful with this. It was a matter of figuring out how the magnetic weight fit into the assembly. That's all it was! Now we have an extra spring for the future.