GO106 Jenn-Air Cooktop - Instructions

Although only one side hinge had snapped, I replaced both sides with new oven door hinges. Followed the website video installation directions and all went well; the new hinges work perfectly.

removed blower housing secured to floor with two screws then removed flexible vent pipe from blower housing then removed blower removed blower wheel and motor put new motor and wheel on put back on stove thats it..

To replace the knobs was easy simply pulling the old knobs of and pushing the new knobs on. Replacing the on off lites was a little harder. i had to remove the control box that the knobs were mounted on. follow the wires.One lite for the left side and one lite for the right side. The left side lite was hooked to the two left side controls and the right side lite hooked to the two right side conrols.The wires then went down under the unit to the electrical junction box and wire nutted to the main wires servicing the range. What I didn't realize is that the left front contrlo knob is the only one that controls the fan.It has fan onthe knob. the rest of the knobs are not to have fane on them.I didn't notice this when I made out the order now I have all four knobs that have fan on them.

Bought a pair for needed door hinges for replacement. Found a DIY video on You Tube showing technique to replace. Door removal was a bit awkward but hinge replacement and door reinstallation was as detailed in video. Could not nor would not have tackled this project without video. Premium quality parts sent and received within days of ordering. Wife happy therefore so am I.

Took parts off from under the range, and replaced the motor. Then put the unit back under the stove and connected the vent.

Everything went fine. No trouble.

Easily removed the switch housing. After that, the other experiences really helped me as the retainer rings on the old switch would not come off and I broke one of the threaded posts about a eight of an inch from the base. I pried the other one off, more carefully, with a screw driver and a vice grip pliers . I was already to use the "super glue" solution when I luckily found an old nut that fit the one remaining threaded post.

The only problem was the little push nuts that came with the new part were too small for the posts on the stove top. I had to go to hardware and buy some for about 10 cents that fit. Other than that, everything was great. Great service from this company!

Opened oven door, took four screws out of the front control panel, removed the two screws holding the burner control switch to the front panel, removed the wires from the old switch one at a time and installed them on the new switch. secured the new switch to the front panel, put the four screws back into the front panel, and closed the oven door. Real easy repair.

I watched a You Tube video,removed and dismantled the door, installed the new hinge. I forgot to remove the small pin which is similar to a rivet. When I tried to close the door it bent. Eventually, I remembered the shipping pin and pulled it out with any damage. Believe it or not, I had read about the shipping pin on customer comments on PartsSelect...Good luck, it is relatively easy!

It is so easy. Once I found the right size of filter from the website, I ordered it right away. It came in 3 days and I just need to take out the old one and insert the new one. No instruction is necessary. By the way, the price of the filter is one third of that from Jenn-air.

Removed two nut screws (accessed with oven door open) with nutdriver, panel dropped out. Transferred wiring one-by-one to new switch, removed old switch with allen wrench, installed new switch, replaced panel. Done! However, the problem is not corrected and all other possibilities have been explored with no solution in site. Ideas needed.

Took less than 15 mins to remove the old switch and replace for the new one.
Works like new!

My wife help take the door off. It was a little heavy . The door came apart very easy and went back the same way.We save over $300 by doing it our selfs.

Un screwed the two screws in the downdraft section enough to release the unit that holds the surface burner controls.Then removed the control nob, unscrewed the two screws that holds the switch in the unit, removed the wires, making sure the color of the wires were placed on the same contact point. Put it back together and it worked
fine.Of course I did shut off the power before starting any of the above

Disable cicuit! remove 2 screws on control housing, lift housing. Remove retaining washers from mounting posts (a trifle difficult, but drill into them with an 1/8" bit...they'll break off enough to grab with needlenose pliers). Mount & wire new switch. The replacement retaining washers are too small...hold them in visegrips & ream the hole with a larger drill bit. Place washer in a magnetic hex drive bit, align over post & tap with hammer to start them, then use a small socket to tap them home. Screw down control housing. Enable circuit...voila!