GMC275PDQ2 Whirlpool Microwave Oven Combo - Instructions

I was able to remove the old element and planned it with what little time off that I could. This would have been maybe 20-30 minute repair at the most. HOWEVER! I was extremely irritated screws were not included? When I called to ask if they were missing they said they didn’t come with the element. Cost me a very annoying trip to the hardware store. Not sure if I missed it on the site that they don’t provide screws - would have been nice to know that before I started. Still scratching my head as to why screws wouldn’t be included? My old ones were as beat up as the element I replaced. I was so irritated I was looking for a spot to leave feedback. Product is fine. Shipping was fine. Sending these products out as they do? Zero stars on that.

This oven probably was manufactured in the '60s when the house was built. The door doesn't just pull off like the newer models. These pins fit into small holes on the oven hinges. I inserted the pins and lifted the door to a 45 degree angle, before pulling the door completely off. Now that turned out to be the easy part. I then proceeded to completely dismantle the door. It actually has 4 glass layers which had to be cleaned individually. The hardest part of all was actually remembering how to put it back together again. I put the door back on just as I had removed it, then took out the pins, and I was finally done! This was not an easy project, BUT the results look great.

I turn off the power in the breaker box and then unscrew the part and replace it with the new one

Installed new part

I put the tray in the microwave???? Pretty easy.

Removed the door from oven removed screws from door and replaced the old hinges with new ones perfect match

The tech said he used No 2 Phillip's. Once I took the door off and removed the racks I quickly learned a Phillips was not going to work. I am now the proud owner of a Kobslt star and square ratchet screwdriver.

Watched the repair video and started the project. Ran into a problem when trying to remove the interior panel off the door to reach the broken interior glass. On this model Kitchen Aid there is another section that is screwed in holding the exterior glass pieces in place. It prevents the interior panel from coming off the front of the oven door. So we had to flip over the door and unscrew the glass retaining bars to get the interior panel off and reach the glass. This allows the entire door to come apart in pieces so you have to carefully line up everything to re-assemble the door. Part of the issue with this is some of the retaining screws are not very long so you have to press the pieces back together to make sure the screw will catch in the original hole. We had to do this twice to ensure the interior door glass was laying flush on its mounts. A bit fiddly for sure, and if I was working alone it may not have been successful. But at least we know how the door is put together!

1) Removed the trim pieces (2 screws). 2) removed the 2 screws holding the oven in the wall. 3) Slid the oven out of the wall cabinet 4) removed the back panel of the oven ( 10 screws. 5.) removed the old thermostat (2 nuts) 6.). Installed the new thermostat and reversed steps 4-1

we live in Venzuela the ordered windows come to us via a forwarder in the US, one glass (the outer glass) still has to arrive. Very pleased with the service of PartSelect, one glass was in stock, the inner glass had to be ordered with the manufacturer. This glass is on its way and will arrive here in Venezuela by the end of May. As I have to travel to Europe next week, I will install both glasses upon my return somewhere in August next. I will sure inform you about the repair which will be done by myself.
regards,
Titus

I shut the power off first as this is 240v. Then removed all the screws that hold the element on. The old one had 5 screws. For this part you will need to buy new or reuse the old screws. I reused the old ones. Once loose the element pulled forward and exposed the connectors. I used pliers to pull the broken one out as it did not come out with the old element. It will only pull out a few inches, but that is enough to unplug the connectors. After unplugged the element can be taken to recycling. The new one can be set in the oven with the connectors near the wires and plug the two sides into the connectors. Have a screw ready and slide the rear of the element back into rear which will support it while you insert one of the screws into the front support to hold the element in place. Then move the element and support as needed to install the remaining screws. Once it is all tight, turn on the power and make sure it works.

I watched the video on the product page and followed it step by step. Not difficult at all.

Unplugged old element unit and plugged in new element. Took two needle nose pliers and a flexible body. Took about 5 minutes. Works fine. Anybody can do it. Make sure power is off at the box.

Several professional appliance repair people told me I had to get a new oven (double, no less!) because "they don't make that hinge anymore." That would have been a $4-5K investment to replace two ovens that both work fine. I'm not generally a DIY person, but was inspired by a FB page I follow called "Handy Women." I got the model number out of my oven, googled "replacement hinge for ____," and found it on this site right away. $120 and about 1 week later I had my hinges. I found this video in the comments on this website that shows (without narration) exactly how to change the hinges.
https://www.youtube.com/watch?v=XzQuU2gZYhk
The only mistake I made that cost me some time had to do with the little pins you have to put into the hinge to remove and replace the oven door. They were missing from the old hinges, and it didn't occur to me to use the ones that were in the new hinges (hadn't unboxed when I started.) I used threaded bolts that were the right diameter and length. They slid right in, but then when I went to take them out, it was an ordeal with WD-40 and an Allen wrench. Then it still didn't occur to me to look at the new ones, so I went to the hardware store and bought two more things the right size without threads. Of course when I took the new hinges out of the boxes they already had the little pins in them. Annoying and time consuming rookie mistake, but my oven door now closes just fine, and I'm getting a ridiculous amount of satisfaction from my little repair job!

Easily, Removed the oven with help of my grandson, this model is quite heavy. Open the back cover panel, removed the old blower. replaced with the new blower, covered with the back protective panel. About one hour because some screws much harder to reach.