The door strike on your washing machine allows your washer door to lock properly, and operate efficiently. If you notice that your washer door will not open or close, leaks or the washer will not star...
This kit is used for front load washers and includes 2 dual-stage shock absorbers, 1 spare shock mounting pin and 4 locking nuts. These shock absorbers keep the washer from vigorous shaking during it's cycles.
This door lock and switch assembly is manufactured to lock the door on your front load washer to prevent it from opening while it is running. You may need to replace the door lock and switch if the do...
The pump is what your washer uses to remove the water from the tub. This part is the pump and motor assembly which includes the red flapper to prevent drain back flow.
Also known as a Door Boot Seal and is used in front load washers. This part is used to keep the clothes inside the tub during the wash cycle. The folds in the bellow allow the tub to move separately f...
This is a replacement screw for your washer or dryer. The screw is approximately half an inch in length and is a Phillips-head screw. It screws in from the outside of the drum, into the vane/baffle. T...
Ask our experts a question about this model and we'll get back to you as soon as possible!
5 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Pat
December 21, 2019
I select the cycle, close door, hit start, door locks and display lights up, but all i hear is a buzzing sound. Machine does not start to fill with water.Thanks
For model number GLTF2940FS1
Hello Pat and thanks for writing.
It sounds like it could be a faulty door strike S890617 and /or water inlet valve PS1145692 you should check for signs of damage, and replace it if needed. We hope this helps. Please contact us anytime.
Good morning, i sent in a question the other day.Washer will not fill, i replaced door strike and door latch assembly, water still does not fill. i checked the voltage going to the water vavle and its not 120 vac, i don't get a good reading on all 3 connectors. . i also checked the continuity on the soleniods on the water valves and they all show open(not sure if i believe all 3 to be bad).do you think the control board is bad. any ideas on what i can check next>
thanks and happy holidays.
For model number GLTF2940FS1
Hello Pat,
Thank you for your question. If the readings on the water valve solenoids are not good, you would need to replace the water inlet valve for your model under part PS1145692 to fix the washer. We hope this helps!
Was this helpful?
Thank you for voting!
Jeffrey
December 24, 2019
The serial number of my machine is xc91007521 the top of the handle came off the machine because the plastic housing for the screw that holds it in place broke (pretty cheap i think). Be that as it may, i need a replacement handle and do not see it on the website. Help please! thank you!
For model number GLTF2940FS1
Hi Jeffrey, thank you for your question. Here is your door handle: PS1145959. Good luck with your repair.
Hello Miguel, thank you for contacting us. The E47 error code on a Frigidaire washer indicates that the control board is unable to detect the door lock.
This could mean that the door lock assembly is faulty, or that there is a problem with the wiring between the control board and the door lock. The door lock assembly on a washing machine is an electrical part that prevents the door from opening while the machine is in use, and also helps to ensure that the machine is properly sealed during the wash cycle.
To fix this problem, it is recommended to check the door lock assembly, part number PS12364048, for any visible damage or malfunctions. Make sure it is securely in place, and clean it of any debris. Also, try a hard reset by unplugging the appliance for 5 minutes. If this does not help, replacing the door lock assembly is the most likely solution. Customer service is available 7 days a week if you require assistance placing an order. Thanks again for reaching out!
High speed spin does not work. Door locks, drain works, normal spin works.
For model number GLTF2940FS1
Hi Steve, thank you for the question. Based on our understanding, we would recommend checking the washer control board, part number PS2330931. It manages the washer's functions such as filling, washing, draining and spinning. You may need to replace it to fix the issue. Glad to be of help!
This was one of the simpliest repairs I have ever done taking less than 5 minutes to complete. On the inner door I removed the two screws that hold the plastic catch in place. I then removed the broken catch and put the new catch in place. Finally I replaced the two screws that hold the catch in place and it was done.
1. Unplug unit. 2. Unscrew 2 nuts holding top in place in rear of unit using phillips head screwdriver. 3.Slide top back and remove. 4. Open door of washer and unscrew 2 screws holding in door lock unit. 5.Pull out unit from the top and install new unit reconnecting the 3 wire connections.
remove top of machine by removing 3 screws along the top edge in the back of your machine and then sliding the top back and up. Then loosen the screws holding on the control panel enough to get to the 2 screws at the top of the door panel. Next remove bottom panel by removing 2 screws along bottom edge then pulling it free from snaps. Then along the outside lip of the bellow, just inside the door, is a wire clip that is easily removed by prying it past rubber lip with a screw driver and lifting it away. Remove the door panel by removing the 2 screws you exposed by loosening the control panel and 2 more along the bottom that were exposed when removing bottom panel. After the door panel is removed and the bellow is completely exposed, you will find that it is held in place by a circular spring which wraps the whole way around the drum opening. Again it can be removed by prying it out away from the groove in which it sits with a screw driver. Now your machine is broken down as far as it needs to be. From here you can follow the directions included in your new bellow kit and put it back together by following these instructions in reverse.
