Models > GLSP84900 > Instructions

GLSP84900 Whirlpool Range - Instructions

All Instructions for the GLSP84900
106 - 120 of 122
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Duel Burner , Inside Burner Out
Removed burned out burner, replaced new burner tested works fine
Parts Used:
Dual Surface Element - 2500w/1200w
  • ROBERT from MOSINEE, WI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Light bulb failure
Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.
Parts Used:
Light Bulb - 40W
  • Grant from Alexandria, VA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Wheel broke off oven drawer
I got the new wheel and screwed it in by hand. It took like 4 minutes total between taking out the drawer, screwing the new wheel on, and putting the drawer back in
Parts Used:
Single Drawer Roller
  • Matthew from Plainview, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Center of Front Burner not heating up
Ceramic cooktop: Turn off power to the unit. remove long "locking" screws from underside of the unit; remove clips (may take a little effort if they are "frozen" in place) From underneath unit lift it up and out of the counter - do not try to lift from ceramic top- remove 4 control knobsun - remove 12 screws (3 per side) attaching ceramic top to the unit - carefully work ceramic top off the bottom frame; its a friction fit - do not force it. Place ceramic top in a safe, flat space. Note the orientation of the burner - you will need to replace the new one in the exact same orientation - also note the connections on the existing unit and match them to where they will go on the new unit. (note: my old unit had a black wire that was replaced by a solid metal strip) work the wire clips off the existing unit, flip it ove and note the number on the "clock face" where the spring clips attach. You may need to drill a small pilot hole from the top side. remove the spring clips from the old unit and place them on the new unit. These clips align the unit in the proper location and provide proper contact with the bottom of the ceramic top. Replace the top gentley working it onto the base and replace the 12 screws. Place the unit back in the countertop being careful to lift up to reposition so you don't disturb the foam tape along the edge of the opening. Replace the clips in the side of the unit, replace the mounting screws, replace the control knobs, turn power back on. You should be done. Takes about 30 minutes.
Parts Used:
Dual Surface Element - 2500w/1200w
  • Bob from Aberdeen, NJ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
27 year old Chambers Oven, Chambers out of business, Whirlpool helped
The oven light gasket had deteriorated with time and bulb changes. It is a self cleaning oven, which gets very hot during the cleaning cycle. The oven is old (27years) and off the "books" I selected a similar, but slightly smaller gasket (3" OD), and "fit" it to the 3.5" light fixture of the older oven. The gasket material was similar to the original, and I used a usable portion of the original,along with the new gasket to build a gasket for the light lense. Several years prior to this repair, I replaced the oven door springs. Whirlpool, who had taken over what was left of Chambers, had the springs. I did replace one heating element about 15 years ago. The Chamber's salesman told me that the Chambers was the "Cadillac" of all ovens, and it seems to keep running.
Parts Used:
Light Gasket
  • Donald L from Lancaster, CA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Inner Oven Door Was Cracked
Step 1. Always ensure appliance is unpluged from power source. 2 Remove oven door by open slighly and lift up be sure your hands are up from hinges they can snap back and injure fingers. 3. Have a cover on a flat surface and have a diagram of oven door, 4. Remove bottom screws and slide out top glass and side rails. 5 Remove top cover and insulation over glass. Beware of any jagged glass. 6. Incert new glass. 7. Be sure when replacing insulation and cover that cover in under tabs to ensure glass is firmly held in place repeat steps in reverse order. Took just 20 minutes to repair. I used a small electric screw driver.
Parts Used:
Range Inner Door Glass
  • Richard from Melbourne, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
range installer broke a screw off & busted the plastic piece
Had to screw off old terminal block & screw on new one
Parts Used:
Main Power Terminal Block
  • Christina from West Des Moines, IA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
The inside oven glass cracked down the middle
I was able to remove the door by opening it partially and lifting it up while jiggling it. Once off, I laid it with the inside up on a table and the screws along the bottom facing outward so I could access them easily. I removed the various screws and porcelain covers and sides feel of easily. The inside panel lifted off exposing the inner glass and frame. The screws and clips had to be sprayed with penetrating oil to remove them. The frame lifted off and the cracked glass was removed. I was careful to wipe away all the fluid used to loosen the frame clips. Assembly was the reverse of this being careful to let pieces fit nicely without force. It would have cost me $39 to have the repair performed assuming I could get the door off. A Phillip's head screwdriver was not adequate to remove the frame clips. You needed a correctly-fitting square drive.
Parts Used:
Range Inner Door Glass
  • Phillip from Fort Wayne, IN
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Inner door glass
Took door apart no problem had a little trouble putting it back together just one piece I put back wrong had to start over not to bad still took less then one hour
Parts Used:
Range Inner Door Glass
  • Anthony from East Islip, NY
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
broken inner glass in oven door
ordered replacement glass. removed oven door. dismantled parts, replaced glass and reassembled door and reattached to oven.
Parts Used:
Range Inner Door Glass
  • Joseph from Slidell, LA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
circuit breaker blew
I went to the source of power on the stove and noticed one of the terminals had come loose from the terminal block and had shorted out against the cover of the terminal junction. After prying the loose terminal off cover I ordered new terminal block and received it the 2nd day. I removed the old terminal block and replaced the part in about 10 minutes..Thank you Parts Select for your easy to find diagrams and quick delivery.
Parts Used:
Main Power Terminal Block
  • Richard from Sarasota, FL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Broken Oven Glass
Per the instructions listed in your customer replies
Parts Used:
Range Inner Door Glass
  • John from Bloomington, MN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Gasket for oven light wore out and needed replacing.
I very simply replaced the gasket where it belonged and I was good to go!
Parts Used:
Light Gasket
  • Karen from San Jose, NM
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Damaged Socket When Removing Bulb Base
This is a built-in oven, so the biggest problem was figuring out how to remove it from the cabinet. The solution turned out to be removing the cooktop above it and unscrewing two screws that connected the oven to the inside of the cabinet. The other problem was removing BOTH metal backs from the oven. The first one was easy. The second one wasn't. The old socket was recessed behind the second back, making it virtually impossible to access the metal "wings" that hold it in place, so I ended up pulling out the socket assembly from inside the oven with pliers.
Parts Used:
SOCKT-LITE
  • Charles from Oceanside, CA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Inner door glass broke from contact with cooler liquid.
I followed the instructions submitted by other users which were helpful. Two notes that might help someone. 1. To loosen the screws holding the inner door glass, use channel lock type pliers to slightly twist the square bracket the screw is holding. The screw comes out easily then. 2. Note that the flange on the side rails go UNDER the glass door front. I spent quite a bit of time trying to get screw holes lined up with the flanges on top - DUH!
Parts Used:
Range Inner Door Glass
  • Gus from Freeland, WA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the GLSP84900
106 - 120 of 122