GLEFM397DBF Frigidaire Range - Instructions

Unplugged unit and removed back panel with nut driver. Removed door, racks and unscrewed element braces from back of unit. Removed element and installed the new one. Reversed the process and then ran the unit through a preheat cycle to test it.

Self easy

PS Great service Super FAST.
Thanks Jesse

Replacing the bake element in the oven was easy once I figured out which tool to use. I initially thought I needed a hex key but saw from a previous commenter that a nut driver is needed. I was able to attach it to a power drill to unscrew the nuts. once the plate was released it was easy to unhinge and install the new element. Be sure to turn off the electricity as the stove is on a 220 line.

Followed on-line instructions to remove the defective heating element. Some connection tabs on the replacement unit were different than the original. One tab was too wide to accept the stove's slip-on wire connector without fling down the tab width on the heating element. Thanks to some on-line instructions, wire connections to element 1a and 2a had to be reversed. If not for those instructions I would probably have ended up sending the unit back to the supplier, as an incorrect replacement !

Twisted replacement bulb into place easily. Let there be light!

remove power (unplug) remove screws from element unplug element replug new element replace screws reconnect power bake cookies until something else breaks.

I used the socket wrench to remove control panel from back of range. I removed the inside circuit board form the holder and carefully removed the overlay from the thin touch panel. I was able to Matchup the overlay to the circuit board smoothly. Reassembly was a snap. Your site helped me pick out the correct part I needed. Being able to see exactly what I needed and how everything fit together saved me a large repair bill. Thank you so much!!!!!

I replaced the bulb using my hands to twist the bulb in the socket located at the top of the refrigerator.

Your service was OUTSTANDING...Ordered one afternoon, and before lunch time the next day, the delivery man rang my door bell...Thanks a bunch for you excellent service.....

I couldn't unscrew the leveling foot because it was rusted and corroded. The bracket holding it was easy to remove so I took the bracket with the corroded foot off and replaced it with the new foot and bracket. Very simple. I made sure I oiled it so it wouldn't rust again.

I am a DIY kind of wife. My husband works late most nights and I get home in the afternoon. It was really quit simple except for the element plug slipped into the back of the stove. So I had to pull the stove out from the wall and take a couple of screws out of the back and push the plug back through. It was scarry for a minute but it all ended up just fine and we had a wonderful dinner that night.

Step 1 Clear frame surface of any debris Step 2 Back out four (4) screws in bottom of glass holder Step 3 insert glass in to the top and allow to drop into the bottom channel. This may take some finesse Step 4 tighten 4 screws Step 5 clean up area and pick up tools

Watched the repair video on your web site. Used the video as a step by step guide in the actual repair.

Husband very ill in bed. It's up to me!! Got a new bulb at HomeDepot and figured out how to get that wire 'thing' back in and the new glass cover installed. I DID IT!! WOW! My husband has always done these jobs around the house.......but now it's up to me.......and I'm not so dumb after all! I DID IT!! Now everyone who comes in the house.....I show them what I DID!! :-)

Quite easy: Removed the two hex head screws with a 1/4 inch nut driver. Gently pulled the old element out of the rear of the range with the connectors still attached. Next I disconnected the connectors from the element and attached a small "paper binder" clip to each of the connector wires to keep the connectors from pulling back through the "Hole". Lastly, I connected the two connectors to the new element (released the clips) and gently pushed the unit back into place and re-secured the hex screws. ALL DONE! Very very easy....