GLDB958JS0 Frigidaire Dishwasher - Instructions

First I removed the bottom dish rack to gain access to the spray arm. I proceeded by pulling straight up on the bottom spray arm, it disconnected with gentle force. The replacement part was not identical, so I determined that it would work by inspecting hole patterns and heat shield configuration. Then I gently pushed the new spray arm onto the water supply tube making sure that the spray arm snapped into place. Due to extremely fast ground shipping (less than 20hrs from order to my door) the repair was done within 24 hrs! Boy...was my wife pleased!

took the door off after several failed attempts, which is easy to do - 2 scews. Then it was easier to find the channel the gasket fits into.

For all Frigidaire diswasher owners, after taking the door off, I realized it was the seal around the soap dispenser that was leaking, due to stripped screws, not the gasket. I rigged it with silicone caulk, but may have to replace that - looks easy, .

Removed screws and put new bottom gasket in old one just fell out.

I closed on a house a few weeks back. You really don't notice issues with appliances until your living there....the walk through doesn't give you the time to really see anything hidden. Anyway - the dishwasher had appeared to be used to wash grease covered parts from a car so I pulled all the racks and filters out and placed the order for replacement parts. I saved hundreds in obtaining replacement parts verse buying a new machine - and I didn't have to sit around waiting for a repairman to do the work for me. I've made several purchases from PartSelect, and will probably making more in the near futre - Thanks!

Repair was easy. Unfortunately I really didn't need the springs or linkage, but I couldn't see that until I took the dishwasher out from the counter. The springs were not stiff enough to keep the door from just falling open. So I cut about an inch off the long end and bent it into a hook. I didn't need new linkages the old ones were fine. The gasket made the biggest difference and went in very easy. The door will be difficult to close for a few times then everything works great.

Had to replace control board Part#:PS420961 on my Fridgidaire dishwasher. It shorted out and started to smoke. Thank god I was home. Had to turn power off at the breaker first thing. Removed the front control panel and cover. Unscrewed control board cover. Disconnected all terminal ends. (be careful here, the clips for the plugs snap easy and the one band wire just pulls up a little bit so you can remove it!) I took a picture with my phone for reference. Had to cut off two burned terminal ends, strip wires back, and crimp on new ones. I suggest using shrink wrap on them. I then pluged everything back in there spots and reassembled. I crossed my fingers and tuned breaker back on. Hit the start button and she fired right up! All good so far. Good luck!

I disconnected the power to the machine. Removed the bottom access panel and screws holding the dishwaher in the cabinet opening so I could carefully slide the dishwasher out.
Taking note of the pump position at the bottom of the dishwasher I removed the two wire leads, screws and hoses(pliers). I installed the new part in the reverse order and was able to run the dishwasher for a cycle while it was out to make sure there were no leaks.
Dishwasher runs great and the dishes seem cleaner. Fingers crossed.
Thanks.

Popped off the old spray arm ... INTENTIONALLY, and put new one in. Had to lift off small strainer to allow old arm to release! Be sure to turn arm until it clicks into place, return small strainer/clip, and you are in business!
Most trouble I had was getting this old bo
y up off the floor afterward.
Dished so much cleaner now!

Remove and replace the door gasket. Removed the 6 phillips head screws holding the top panel cover. This gives access to the latch assembly. Remove the two screw holding the latch in place. I removed the four wires one at a time with needle nose pliers and plugged them on the right spade of the new latch assembly. This assures getting them in the correct position. I then mounted the latch with the two screws and installed the cover with the 6 screws. Job done, piece of cake.

This was too easy. I pulled out the bottom rack, spread apart the two clips which are at the bottom of the spray arm with my fingers and pulled out the old broken spray arm. The damage was visible. Then I took the new spray arm ( which looked different but still fit nicely) and gently pushed it into place. Done!

It is rather easy to repair. After you remove the screws that secure the top of the dishwasher to the countertop you can slide the disherwasher out far enough to gain access to the hose. The hose pulls off after you slide the spring clips down the hose far enough so they no longer grab. Then simply reverse the order and you're done. Less than 30 minutes and you should no longer have to hand wash your dishes!

replaced with new lower rack, out with the old, in with the new! Shipping was great new part arrived in 2 days! Great service, and will use again for all parts needed in the future, and will tell everyone about this site! Thanks a bunch!

The nut was split down one side, so I first tried to sauder the nut back together. Saudering never goes well for me anyway, but I couldn't get a good enough seal around the nut to make it fit tightly. Then I had to cut off the clear plastic shield to get down in there, just before realizing you could just pull the white wire firmly and it would come loose from the nut. All I had to do then was unscrew the original nut, and screw on the new nut. Then, luckily I had mistakenly ordered an extra clear plastic shield and could replace the one I had previously cut. Dishwasher now runs like a charm!

Manually took off melted parts and replaced them with the new ones.

Intuitive repair if you are one of those people that take things apart & put them back together for kicks. Nothing fancy about this repair, as all the parts have no adjusting. Remove the 6 phillips heads screws on the inside of the dishwasher panel. The front electric panel comes off, leaving the inside exposed with the wires. Unhook 4 wires to the handle. Remove (2) star shaped screw headed screws. (The most difficult part if you don't have this bit.) New handle can only go in one way. Re-attach wires & screw panel back on. The latch required pulling the dishwasher out a couple inches from under the countertop to access the mounting screws. The dishwasher is held in place with 2 screws into the countertop/or side cabinet. Slide dishwasher out. Remove 2 screws and replace. Once again, there is only one way the latch can be installed. All is good, and easily accomplished in 5 minutes....if you have the "star" bit, which does come in a couple different sizes.