GIE18GSNHRSS General Electric Refrigerator - Instructions

I watched your Video. Thank you.

As explained on your how to on the web. Ordered by phone ---A1--Arrived as promised-- The kind of service we used to expect.

Pried the switch on the bottom with a flathead screwdriver, twisted it and the switch came out far enough to take it out by hand. The bottom of the switch has to be raised upward a little because the connectors are on top of the switch. Changed the wires from the old switch to the new one, one at a time. Insert the new switch. Saved a repair call, and probably a more expensive switch. Less then 15 minutes.

Watched video repair by Hotpoint , Everything went like clockwork and was a total success. Repair took exactly 25 minutes.

First thing I did was un-plug the fan motor located in the freezer compartment and test it for voltage, which it had, telling me the fan motor was shot.I ordered the parts, they arrived in short order and the fan motor was replaced. It took little time and there were no levers, pulleys,servos, gobs of wiring or stacks of gears in a maze of bearings to deal with. Unplug the unit, remove the food rack, ice cube maker(just loosen the 2 screws and lift up)remove the air channel in the center as well as the back panel. Unplug the fan motor and remove the screws securing the motor bracket and lift out. Very simple.

Actually watch your video and it was really easy.

I replaced the noisy evaporator fan motor after watching the video provided. All went well and now I have a much quieter refrigerator. I took apart the old evaporator motor to see why it rattled when moved and it had an electrical part that came undone and was the cause of the obnoxious noise that came from the refrigerator. Now, my wife and I can sleep better now that the noisy fan was replaced.

Removed all the freezer inside panels to inspect the motor before I ordered the part. It looked like a relatively easy job to change it. I also watched the really nice video on the website that re-inforced my confidence in doing the job. The part came in a few days. I disassembled the freezer interior exactly as the video showed.(Warning: be careful with the styrofoam piece if the fridge is not fully defrosted. The ice build-up could cause it to break when trying to pull it out!)The only problem I had was getting the little collar on and off the motor fan shaft, and getting the fan off the shaft. I had to pull really hard for it to come loose and then I had to push really hard to get it back on the new motor shaft. I didn't know if could have used any kind of lubricant or not, so I didn't. After that the re-assembly inside the freezer went well, being careful to put everything back in the correct order and position. Started the fridge back up and it has been running very quietly ever since. But, most important, my wife was impressed with my work and is very pleased with the result!

First I looked at the video on changing out the fan.Made a lot of difference. Everything was covered and made it simple. Wish I had gotten two grommets but the back one was in good shape and worked fine. My hearing isn't great but now I can't even hear the thing run unless the freezer door is open. The shipping was great! You sent it out immediately and in a few days it was here.

I simply followed the online video instructions.made the job easy and fun.

watch the video very good

I followed the instructions in the video. The decorative parts were slightly different than in the video, such as screws at the top versus the bottom, but all of the working parts were the same. I was somewhat hesitant about applying pressure to remove the locking spring and fan blades and to replace them but the video reassured me and all went well. The refrigerator is operating as quietly as when it was brand new.

Ordered the part and within three working days the part was delivered. It took two minutes to pry off the broken part and one minute to snap in the new one.

replaced with new one

It really was as simple as the other folks noted. Slid a screwdriver into the edge of the broken switch and it popped right out. Disconnected and reconnected each of the two wires and just slid the switch back into the slot. Truly a DIY fix.