GGE388LXB02 Whirlpool Range - Instructions

This range was easy. Only 4 screws under the front panel that allows the panel to come off. No need to pull the range out for back screws.

Replacement part was exact and worked perfect.

Turn off the circuit breaker for the range.

Remove the 4 screws under the front panel, one on each end and one one each side of the display/control panel.

Pull the bottom of the front panel out about 30 degrees and lift off the top.

Once panel is off pull of the dial knob, remove the two screws for the control and swap wires on at a time with the new one.. Reverse the procedure and all is good. You may need to use needle nosed pliers on the spade connectors if they are too tight to pull off by hand.

Slide range out to access rear. Turn off circuit breaker and/or unplug stove. I did both. Removed four screws on top section on rear of range and CAREFULLY slid out the back plate. Disconnected all wires and plugs from old switch noting locations. Placed wires and plugs on new switch. Removed knob and then two screws from front of old switch. Carefully placed new switch in proper location and screwed in the two front screws. CAREFULLY place the back plate in proper location and reattach with four screws. Clean floor and cabinet sides while range is out. Plug in range and/or turn on circuit breaker. Test switch operation and verify Cooking Surface On light only lights when switches are on. Slide range back into place.

I shut off the breaker to the stove. I removed 2 screws from the underside of the cooktop at the front of the unit. I raised the cooktop and had my helper hold the top at an angle to access the burner. I removed 2 screws attached to the burner and then loosened the 2 clips and moved them to release the burner. I transferred the electrical connections from the old to the new. Reinstalled the burner and cooktop. Turned the breaker on, tested the new burner and I was fone

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

unplugged power took the back panel off unplugged the 5 wires removed knob by grabbing and pulling off took two screws out of front panel removed the switched put new switch in place and reversed the procedure went very smooth know problem at all any one with any kind of ability should change this switch in know time at all

Removed old racks, installed new racks. Recycled old racks.

removed 4 screws lifted off the face with switches replaced the bad switch and put the face plate back on. if you have any concerns just watch the video , part select has posted its great

Video said to remove screws and lift stove top off, remove contacts and ground. My stove top was hinged and required me to lift and pivot stovetop up. The burners were anchored to the stove base not the top. I secured the topso that it would not drop down and proceeded with repair

I followed the instructions as provided. When I finished I noticed the switch was 1/4 turn out from the off position mark on the stove. So I pulled the stove back out and took the back panel off again pulled the knobs back off took out the screws that held the switches in place and rotated the switch 1/4 turn counter clockwise. Then I replaced all the screws and knobs . Then I replaced the panel and shoved the stove back in place. One of the burners was an eight inch and the switch doesn't work as well as it could. However there was not a direct replacement for the eight inch burner.

removed several screws, removed old controller, installed new controller buttoned back up works perfect

Put the back of stove on blocks of wood to get high enough to screw the new leg in.

replaced control

Replaced the oven light with a new one but it burnt out as soon as I turned it on. Therefore I decided a new socket may help.

My whirlpool apparently has the old style socket which is pictured in partselect part #PS12584564. The old style socket has to two metal arms that retain it against the metal reflector.

The part that will come (#PS12584564) however is the new style that whirlpool has changed to, apparently. It is not as pictured. The socket and the reflector have different retention devices.

I used screw drivers to bend the two metal arms away to release the socket. Then I had to use allen wrenches to bend the reflector's retention tabs away.

Once I had the old socket, reflector, and lens replaced I just followed the video on partselect for part #PS12584564

Had an electrician to do the job for me.

Turn off 220 voltage, unplug and remove clips. replace it with new part. Check part before replacing the top of range, if it works, the electricity can be turned back on. Repair done.

Changing out the switch was easy. Paid attention to wire connections to avoid mixup. Removal and installation of the switch was easy. It's the back panels that gave me the most challenge. Used screwdrivers and needle nose pliers to do repair. Having a second set of hands for the two part back panel reinstall was most helpful, but can be accomplished by 1 person.
Burner works great. This is a easy DIY fix.