GFDN245EL0MV General Electric Dryer - Instructions

The clothes would get caught where the drum slide should be (it was almost totally worn down) and would leave black marks. I watched Parts Select youtube video. Bought the parts needed from Parts Select. They arrived within a couple of days. I replaced the 2 drum slides and no more getting caught. Took about 20 minutes.

Faulty Door switch. Dryer would heat up so I knew it wasn't thermostat or element related.

There is a plastic female closure part in the dryer door that wouldn't close tightly around the metal male closure on the dryer. I popped out the plastic square with a screwdriver, popped the new plastic closure in with my thumb. Works great. I never even installed the new metal portion of the latch.

Easier than I thought it would be. I was hoping it was the front bearing because replacing the rear bearing looked pretty gnarly. Unplugged the dryer from the outlet. Removed two screws inside the door frame. Lifted the top off. Unscrewed the two screws holding the front on. Lifted the front panel off, careful of the wires going to the door. Popped out the old front bearing by releasing the two clips at the top. The old bearing was pretty trashed. The two grey/green slides were in tatters and one of the white ones was missing. Not too much lint inside the dryer, but the lint trap was pretty clogged. Cleaned the insides out with the shop-vac. Inserted the new slides into the new bearing an snapped it back into place, careful to make sure the light went in the hole. The felt gasket at the botton was in good shape so did not replace it. Replaced the panels screwed them back to together and it fired up smooth and quiet.

Great service. I got the part in 3 days and having the youtube video was fantastic. I also was able to find other videos also so doing these tasks yourself nowadays is much easier. I was a bit nervous but it turned out to be easy.

I went to replace all four of the drum slides but in the process of doing this, found out that the whole of the top support had been rubbed away! I therefore ordered a replacement top support and replaced it per the instructions in the PartSelect webpage and from the youtube demonstration and completed the repair. I had a little trouble with getting the top support installed, but by jiggling it around and persistence I was able to complete the repair. The help I received on the webpage and video were invaluable! Thank you to PartSelect and to the other users for all your help!!

Watch the video on how to replace the belt on PartSelct site belt installation page.

Followed the video which made it real easy.

This is the 2nd time we had to replace the slides. Not a big deal. Removed the top & front of the dyer and replaced the new slides. It's also a good time to vacuum out the inside while you have it apart. Be advised.... Get your tools ready. You'll be receiving your parts quickly. Couldn't believe how fast they arrived!

Removing the top and then the front of the dryer went fairly easily after finding the screws. The drum came out with just a little coaxing, does not gets screwed in place. To me the trickiest maneuver was getting my hand under the drum to place the belt over motor pulley and around the tensioner pulley. You must look up an image of the belt routing. It took me forever to figure that out. If not for that, this in a half hr fix. Ps don't forget to unplug the dryer.

It took a while to diagnose the problem. I finally figured out it was the door switch by pushing it with my finger with the dryer door open and starting the dryer. It would run like that, but the switch was not being pressed in enough by the door. I ordered the switch and I should have been able to replace in about 15 min. But the old switch broke while I was removing it and it fell back inside the unit. So I had to remove the top and the front panel to access the door switch. That's why it took so long. If that had not happened it would have been a much simpler repair.

Googled possible problem where noise was coming from. Went to Parts Select web site. Ordered felt and drum bracket. Removed screws behind control knobs and removed top of dryer. Removed two screws on front inside dryer (left/right side) this allowed me to remove front panel of dryer. Unattached wires. Drum bracket is located above door opening...pretty much snaps out, felt piece is located on bottom bracket. Felt piece was replaced and new top bracket replaced. Reattach wires, lift drum slightly to fit doo iInto place. Dryer still made noise. Noticed I did not have any drum slides! Drum slides slide into top of front bracket at 10/2 o'clock position and 11/1o'clock. Easy and very inexpensive dryer repair!! My husband was very impressed that I could take dryer apart and fix!!!

Unscrew the top panel parts three screws. Then another three or six screws to get to the dryer front which needs only to lift straight up about two inches. Pull back slightly and replace the teflon slides. To replace the slides they lay on a tiny plastic pin and slightly bend into the slot to hold them in place. Reseat the dryer drum. Reverse the process to make it like new. From the time you start hearing the dryer squeak, BE CERTAIN to replace these within a week or two (depending on usage.)Otherwise, you may wear out the housing where the teflon would rest. If that happens, you will be out more money to replace the housing and a lot more time to install. Been there and done that. Trust me.

Parts arrived well in time, exactly what was needed. The latch was a snap-in process. The strike require gentile use of a pliers, and went in quickly. Thanks!

I removed the top of the dryer and saw that the top two drum slides where gone and the drum bearing itself was damaged I Temporally placed the parts on the drum bearing until I got the new one, that stopped the squeaking noise. All I needed to do was place the part with the hole on the little hook and then sled the other part in its slot.