GDWF100V70WW General Electric Dishwasher - Instructions

I watched this video: https://www.youtube.com/watch?v=-k0iZGwMOGc
And then I did exactly what it said! It was easy. Plus, when I opened the panel I could see the old switch interlock assembly was melted on one side, so I knew I had gotten the right part!

Watched the video, and followed the directions. Although my machine had some slight differences, the repair went pretty much per the video. Got all connections back where they belonged, cleaned up the insides a little while had the door parts separated, then buttoned it all back up, ran a cleaning solution thru empty washer, let it dry then started filling with dishes and ran the wash cycle the next day when full. All is well.

I had a shut off water supply shut off shut under my sink. That is where I shut the water off for the dishwasher. I knew it was for the dishwasher ,because it follow the line, and could see it was going to the washer. Then I went down stairs in the basement. Opened my breaker box, and found the breaker for the dish washer marked dish washer, and put in the off position. When I was still up stairs I opened dish washer , and inside at the top was two screws holding the dishwasher to the counter top. Those two screws turned out to be the exact size of just about every screw I ended up having to unscrew on this machine. So at the time I was in the basement turning off breaker, I went to the garage to gather up tools. Take the two screws that are screwed to the counter top. Then I layed on the floor, and at the bottom of the dish washer there is a panel on the front of the machine with screws attaching it. Take those screws out. Pull off cover. Now get a flash light so you can see. They're adjustable feet that the dishwasher are being leveled by. Those feet need to most likely be adjusted down so you can the machine pulled out, and make it possible to work on. now you can you can pull it out, but watch that water supply line does not get hung up, or electrical wires. Once the machine is pulled out there is another cover on the front that I took off. Four screws hold it on. Now you can get to the part to fix it. The other thing you need to know is after taking off the valve and taking off the old 90 fitting. It will need cleaned up. When you put it on the new shut off valve use pipe dope or thread tape so it doesn't leak. Good luck.

Really all it took was removal of the old wheels which would not stay on anyway and the installation of the new ones. That required the axle and wheel being put together and the installing both of those on the lower rack. I was about to buy a new dishwasher when the salesmen told me about a product called Lemi Shine it saved my hundreds of dollars and the inside of my dishwasher looks brand new. With my new wheels I am good to go again.

Simply pull out the old axle and snap in the new one. It is simple. Also the replacement axels were MUCH better quality than the originals. The bottom tray now slides in and out very easily. Note, if you have this problem, you do not need to replace the wheel, just the axle.

but axle on new wheen and put axle on tray

I simply removed the old (broken) stud rollers by pinching them with a needle nose pliers and pushing them out, snapped the new stud roller in the wheel, and snapped the wheel onto the lower basket unit. If you have all of the wheels and they are in good shape, you do not need to buy new wheels, the new stud rollers work just fine with the old wheels.

This was a simple part swap. The stud rollers are the small peg-clips that hold the wheel on the lower dish rack. Removing the old stud rollers from the wheels required a pair of pliers. I then popped the new stud rollers into the old wheels and snapped them back onto the lower dish rack. I scored some major points from my frustrated wife -- easy, fast fix!

Repaired the soap dispenser.

We received our parts for our dishwasher within 2 days. It was very simple to find the parts on your site, and very easy to install. Our dishwasher is back to normal and the racks roll in and out easily. I would recommend ordering from PartSelect to anyone.

No instructions. At first thought I needed instructions. A minute later I was attaching the new rollers. Simple and easy. Took less than 15 minutes. Would recommend these rollers.

Used teflon tape around new 3/8 elbow. Re-installed valve in originals postion. Connected supply hose and reconnected electrical to valve.

Removed the existing stud rollers with the wheels attached. Then removed the wheels from the stud roller. Then snapped the wheels on the new "Better Designed" stud rollers. Then easily snapped the new stud roller assembly in place. Piece of cake...works like a charm.

Thanks,

Randy

Removed empty basket from dishwasher. Placed basket upside down and removed remaining wheels from basket by detaching worn axel from attachment points. ie, No tools needed for this procedure. Once axel and wheels were removed, I squeezed the end of the old axel with needle nose pliers or regular pliers to relieve the outward pressure and pushed the old axel out of the wheels. Easy, popped right out.
Positioned new axel against the outer wheeel hole and applied thumb/finger pressure to snap in new axel. Took the wheel with the new axel and
attached it to the basket at the original position. New axel grips the basket like a clothes pin would.
Continued and replaced all eight axels at this time.
Replace basket in machine, stand back and admire work and parts!!!! Parts received promptly with no hassels. Excellent company to do business with, clear photos and ordering forms.
Will definately re order again if needed. Thank You.

Replaced interlock assembly as one of the possible causes. The replacement was easy, but this was not the final fix. I also replaced the water inlet valve, flood switch and finally found that there was large calcification within the drain tube assembly (not visible, but was blocking water). Got a new flexible tubing and new drain hose, plugged everything together and the dishwasher runs like new now. Watching for a potential leak from the drain tube to drain hose connection and mya need to tape it up, but so far so good...