This is an end cap for a dishwasher rack. This part is about 2.5 inches long, is black, and is made of plastic. You may need to replaced this part if it is broken, or if your dishwasher rack continuou...
This OEM-compatible screw is designed for use with many GE dishwashers. Measuring 8-16 HXW and 1/2" in length, this stainless steel screw secures the middle spray arm hub to the upper rack assembly, e...
This is replacement door latch for your dishwasher. The door latch is attached to the tub frame, and connects to the door strike to keep your dishwasher door closed during operation. If you have a bro...
This diverter valve assembly controls water flow between the upper and lower spray arms in compatible dishwashers, ensuring efficient cleaning during each cycle. Located inside the appliance, it direc...
This drain pump kit is designed to remove dirty water from your dishwasher during and at the end of each wash cycle. If you’re noticing standing water after a cycle or leaks beneath the appliance, the...
The lower rack roller supports the smooth sliding of your dishwasher’s bottom rack. Measuring 1.5 inches in diameter and charcoal-colored, this OEM replacement part is sold individually. Replace all f...
This dishwasher latch strike is a manufacturer-approved replacement part for your appliance. The latch strike is an important component in your dishwasher door assembly, and adds an extra layer of sec...
This middle conduit assembly, also known as the middle spray arm water supply tube, is an authentic OEM replacement part designed for dishwashers. It is a gray, plastic tube that connects the main wat...
This dishwasher toe-kick plate covers the lower front section of the appliance to create a clean, finished appearance while protecting internal components from dust, debris, and accidental contact. Ma...
No Longer Available
Questions And Answers for GDF640HMM2ES
Be the first to ask our experts a question about this model!
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
This didn't work out well. At the beginning of September the control panel in the door started to work erratically, the lighted buttons did not light up as expected. I ordered a replacement board and installed it. CONFIGURED UI SERVICE CONTROL Part #: PS16618944 This did not help, so I ordered another control board and installed it. CONFIGURED SERVICE MACHINE CONTROL BOARD Part #: PS16226072. This did not help. This control board has a small orange fuse that looks like an old fashioned transistor. it was fine, as was the fuse on the previous control board. There were two things about the Control boards that might help someone figure out what went wrong. When I took out the original control board, there was evidence of component overheating. When I installed the new control board there was a green light that was blinking. I had hoped to complete this repair, but we have been without a dishwasher for over a month, so I bought a new one. (I am a competent Instrumentation and Controls technician) It could be that there is a bigger issue here; a major component failure. If anyone has some suggestions to try, I would like to repair the machine and sell it as a used appliance.
1. Turn off breaker supplying power to dishwasher in electrical panel 2. Open dishwasher door 3. Unscrew the screws that secure the dishwasher to the counter. 4. Tip dishwasher forward. Identify the non-functioning door latch. It looks exactly like the replacement. Unclip the wire harness from the door latch. 5. On the inside of the dishwasher, there are 2 screws directly under the door latch. Unscrew them and carefully set aside. 6. Remove old door latch. 7. Set new door latch in place. Holding securely, replace screws removed in step 5. Toward the end they get a little tougher to screw in. 8. Plug wire harness into new door latch. 9. Re-align dishwasher and re-secure to counter in previous position. 10. Test latch to make sure it closes properly. 11. Turn on breaker in electrical panel. The dishwasher should now function properly.
repair under warranty for Home Depot. Ordered new controller, new sump manifold, new piranh clamp kit, new diverter passive main assy, installation took 6 months. Could not finish as GE had changed the diverter to a new design with the same part number that the repairman had no knowledge of and there is no part available for the same configuration of the one that went bad, after I called GE tech line they were not aware of updates. Giving me the same numbers. The new design works if you order a new conduit main. As the old one in the dishwasher will not connect to the new Diverter. New deverter no. WD19X25278 and the new main conduit is the same as the old configuration no.WD12X21681 . The repair people and parts people are not yet aware of the design change and availability of parts, as most are out of stock and no updated pictures of the new design. Repair warranty washed their hands of this and Home Depot after 6 months gave me credit of my full price I bought this for 3 yrs ago. Repairing myself and sell.
