GDF570SSF0SS General Electric Dishwasher - Instructions

The repair instructions were great and the repair went well. The repair took less than an hour.

Thank you
Gary

I tested Heating Element with Ohm Meter-Direct Short (if open it would have been bad and I would need to replace the element. Per the Website Troubleshooting for GE dishwasher, it said Heating Element (65%), Float Switch (32%), or Computer Board (only 3% Chance of it being board). So I ordered Float Switch. Later I noticed that the dishwasher would not change wash cycles from Heavy, Normal or Light.
So I turned the Circuit Breaker on and off. This fixed the Wash Cycle.
When the Float Switch Came in, I installed it in a few minutes watching the video on the GE Troubleshooting Page. Later when it was running I checked the operation and when I opened the door, the wife says seeing the steaming water, You fixed it, the Water is Hot now ! It was all about Hot Water, not the Heating Element at all ! And I think everything was fixed when I flipped the Circuit Breaker on and off and re-set the computer board. I think replacing the Float Switch was good maintenance, cause it was really dirty and needed to be replaced soon anyway. And it may have avoided my wife's next misdiagnosis with our dishwasher. This was 2 weeks ago, and all is well.
Sincerely,
Scott

Replaced all 3 spray arms in less than 10 minutes.The top one came in two pieces,the mounting bracket and the arm.Snap the bracket on the dishwasher first , then attach the arm to the bracket.

Opened the box took the rack out and placed it in the dishwasher. Good as new.

The dishwasher rack was supposed to come with wheels it did not but I was able to use the existing wheels from the lower rack and snap them on was pretty easy

Followed directions on YouTube

So easy, even I was able to do it. Slide tabs back on defective basket and remove both sides, then slide the tabs onto new basket and place in dishwasher. All Done!

My heating coil was not working so naturally I thought I needed a new coil and ordered one accordingly. During the time it took to ship to me, I did more research and people suggested testing the coil with and ohmmeter for resistance as often times the coil is fine and it is the flood switch that is the problem. I got an ohmmeter and checked the old coil and it returned readings that were just fine (btw 15-30), so I returned the coil and ordered this flood switch.

Anyone reading this debating between buying the coil and switch can save themselves a lot of trouble/time/money by removing the coil and testing it first.

The installation of the flood switch is fairly simple. There's a great video on Youtube for it (titled "GE Dishwasher not Drying Dishes - How to Replace Bad Flood Switch:), so I won't walk through the step-by-step on it.

However, one word of advice is to be careful when installing so that you don't let the o-ring on the switch slide down the connector/wire once you connect them or you'll get a slow leak into the catch pan at the bottom.

Also, if this if your first repair on a GE Dishwasher then get to know the unit while you have it pulled out. It won't be your last repair based on my experience...

The replacement dishwasher basket easily fit in my dishwasher. Easy to order. Quick delivery. Highly recommended.

Installed new heater by pulling unit out of it’s cubby hole. Was able to gain access to the nuts that hold it down and make the seal, as well as the electrical connections. Re-installed. Helpful if you remove both dish baskets and utencil basket for access when installing heater.

Just snapped it in place and that’s it!

The part is held in with two plastic clips, which are easy to unclip. The part needed to be slightly flexed to release it and the new part went in the same way the old one came off. One issue: The replacement part had one extra row of tines that encroached on the silverware basket. As it turned out, one tine fit between basket sections and the other fit through the hole in the bottom of the basket and it doesn't interfere with utensils so it turned out not to be a problem.

After replacing UI board, I replaced the mainboard. still did not solve the problem. The element tested good and I had removed the flood switch, rinsed and blew it out so it rattled but the damage was done. Replacing it made the dishwasher heat water and heated during dry cycle. Removed fine filter, removed course filter, removed two screws with nut driver, removed flood sensor and then reversed. A year or so ago, the dishwasher flooded for no apparent reason, wondering if that was the beginning end of the switch!

First, drain as much water as possible using a shop vac or siphon. Unscrew two plastic lugs and food screen to release the metal *disk* found inside the dishwasher at the bottom. Then, remove the grey retainer ring found under the food screen.
Using the nut driver, remove two screws from the white plastic retainer ring at bottom the flood switch.
I used pliers to grip the ring to take it out.
**Dry everything in the "well" where the flood switch sits.**
Now, remove the bottom front cosmetic panel. This exposes the underside of the appliance. Locate the flood switch wire underneath and gently pull down the small black plastic tab which holds the wires in place. This allows more movement to make your job a little easier!
Pull up on the flood switch and simply unplug it and swap in your new switch! Replace everything as you found it, don't over-tighten your screws, and make your kids load that sucker! Hope this helps, and have a beautiful day!

Took out 2 screws that held machine in cabinet. Pulled out dishwasher about 4 inches. removed old latch and disconnected electric connection. Put in new latch, reconnected electric connection, replaced screws, pushed machine back in cabinet, replaced 2 screws that hold machine in place. Works like new!