GDF510PMD2MB General Electric Dishwasher - Instructions

Popped old bracket off with screwdriver, with a then easy installation of the new part.

Unscrew the upper and side holding screws. Move dishwasher part way out. I didn't need to disconnect the water or electric. Make sure the electricity is off. Remember your working around water. Take off the bottom plat removing two screws, Remove broken cable pulley and replace new. Buy two since your their you might want to replace both. Have fun! It's duck soup.

Some of these other instructions may be for other models. This is specifically for GDT530PGD2BB, which doesn't present screws on the inner side of the door.

I'm extremely reluctant to do anything more than the repair at hand, so I didn't move the dishwasher out of its recessed cabinet, which would make the repair easier. I also did not remove the connector plug from the dishwasher to the door, since there was enough slack to do the repair without this step.

1. Turn off power to the dishwasher.

2. Under the bottom of the door, there are two 1/4" hex screws that can be removed with a small socket wrench, or if you moved the dishwasher out, you can tip it over slightly and get at these screws with a Phillips screwdriver.

3. With those out, you can open the door flat and slide it off it's hinges *just a little bit*. You need maybe an inch or so clearance to slide the old gasket out and slide the new one in. I had to use pliers to remove the old, very damaged gasket, but the new one easily slid into place.

4. Were you able to just move the door out a bit without removing it totally from the hinges? Great! Slide it back, put those screws in the bottom again, and you've done it! Probably in minutes!

5. Or, you could be like me and accidentally lift the door too far and have one of the hinges pop out. If I had someone helping me, it would have taken half a minute to put the door back on its hinges, but I was by myself, so I had to finagle something to keep the hinges open (two screwdrivers wedged handle first), so I could slide the door back on the hinges. That took me about 10 minutes. ¯\_(?)_/¯

Good luck!

I took out the old one and simply inserted the replacement. It was an exact replacement part and thus a perfect fit. Dishwasher is working fine now! Cost was around $40 (shipped) which I thought was reasonable.

Replaced gasket with a new one before further problems occurred. Got to get it in but it was relatively easy to place and snap in just make sure it fits on the right place where gasket inside meets ridges on door so it will be on properly for proper fit.

Very straight forward. After removing the power source the dishwasher was pulled forward enough to access the the door hinge springs. Then the door could be removed and the inner skin separated to access the the dispenser mounting screws.

Looked up the replacement part on YouTube, watched a video and followed the instructions. Part ordered was the correct part and the video showed how to access for replacing. Watched a different video for hooking up the disconnected springs that allow the door to lower and close smoothly. Whole process for repairs was less than 30 minutes.

Removed two latch screws and one electrical connection, Removed
two screws that hold D/W to countertop, pulled D/W out enough to remove the old latch, install new latch, push D/W back into place, rescrew to counter top and rescrew the two latch screws. This problem happened since new, had repairmen twice and they did nothing but move the dishwasher stating it needed alignment, never mentioned this easy repair....

Simply unscrewed the old damaged arm and screwed the new one on, took less than a minute

A quick twist of the locking nut

It took longer to uninstall and reinstall the dishwasher than it did to change out the part

Replaced latch

took off 2 sheet metal on the bottom, lowered the dish washer, pulled it out enought to unscrew 2 screws, unplugged the old part plugged in the new, put it back together.
Works like a champ.

Unhook water line . Turn off power to dishwasher. Remove dishwasher from under counter. Lay it on its back. Loosen clamps on drain pump and remove pump. Install new drain pump and tighten clamps. Be sure to put hanger in the hole on the pump. Very easy job. Reinstall water line and put dishwasher back under counter. Turn on power to dishwasher. Go to go.

Simply pulled the new one out of the box and put it into the dishwasher.