GCVH6260H0WW General Electric Washer - Instructions

Took it apart per the video and reinstalled

followed partselect video instructions. Easy but takes time. Thank you

I won't bother repeating other people's comments. My repair took a bit over 2 hours. I watched 2 different videos and thought the repair was doable. To remove the first wire band holding the boot seal to the front panel I found using an awl to grab the eyelet near the spring was easier than using a needle nose recommended in the video. To remove the second wire band I used an offset screwdriver. One video I watched recommended removing the lower counterweight to get at the band's screw - I did not do that. Putting the new boot seal into the first groove and installing the wire band was the most time consuming part of the job. I did not have extra hands to help. I recommend the second pair of hands for that part to save time. The rest of the install was easy.

The repair video was almost perfect. I would not have even attempted the repair without the video as I am not a handyman at all. The diagnostic feature based on the symptoms was invaluable. I originally took the front of the washer off because I thought the rubber seal around the door was leaking.It was like 67% of the problem. But after checking the front seal carefully, I determined it wasn't. The next most likely issue as only rated 19% but when the water inlet pipe, I was actually tickled to see a crack in the plastic pipe. I ordered on line on Monday and with the cheapest shipping, I received my part in the mail on Thursday. I would highly recommend using Part Select for diagnostic, parts and repair. I will definitely use again. If I could make one recommendation to Part Select, it would be to do a close up during the video when the technician is working with a part, i.e., the wiring that goes around the rubber seal.

Watch the video posted on PartSelect. It was excellent and walked step by step through the whole repair.

I only ran into one issue not included in the video. In order to remove the inner ring holding the boot seal, I had to remove the weight at the bottom of the tub. This is easy to remove with a wrench, but took two people to reinstall. You only need the second person for 1-2 minutes to hold the weight while you align the bolts.

The most difficult part is ensuring you replace the hex nuts and screws in the same location. I took pictures as i removed them to know where to reinstall.

Total repair time was probably 1.5 hours.

My part came in and my husband was at work so..... I did not want to wait for him to come home to wash my clothes! I installed the motor myself and I was not even the one that took it off! It was so easy to do! Turned the washer on and bingo it was back and going! So glad I can get the parts myself and avoid the middle man and his bill!!! Hook up the drain hose with pliers and screw the motor to the frame and that's it!

Before disassembling anything be really sure that the little things are reassembled just as they were prior to removal.....

Sandblasted spider to thoroughly clean it and increase ductility.We used aluminum foil covered in 5200 on one side to cover holes eaten through spider. Then glued the spider to the drum and filled inside rim of spider with a nice layer of 5200. If the spider was made of stainless steel, the washer would still be running great. Thanks

Accessing the door seal was routine. Removing top and front covers was easy. Lower front cover was a challenge because the leaking door caused the screws holding the panel to rust, so extra effort had to be used not to strip the screw heads. Seal removal was easy, replacing the seal was much more difficult. The majority of the repair time was spent attaching the new seal to the drum. It became a tedious task with a large amount of trial and error. Replacing the front spring clamp also takes some time. Eventually I completed the repair and fixed the problem. I will say that if the washer breaks again, it's going to the dump.

Removed old pump and replaced. Did not want to wait 2-3 weeks for a repair person

My husband read all of the posted notes and then went to the you tube video noted by one of the postings. He gives excellent instructions and the video can be paused as each step is completed. The most difficult steps were gaining access to the rear clamp and attaching the rear portion of the gasket. Inserted a phillips head driver bit into a 1/2" deep socket and then used the rachet to remove and re-install this clamp.

Let me begin by saying I'm a woman & don't really think of myself as handy but will try a repair. So at first look we thought we'd have to hire a repairman, but after looking at your website & reading the reviews I realized I could fix it myself (or atleast try). I wouldn't recommend doing this repair yourself without watching the YouTube video showing step by step instructions. It was involved - had to take entire front & top off of washer but overall was an somewhat easy fix. The hardest part to me was getting the 2nd band off of the boot seal primarily due to it's location, so when I put band back on I tried to adjust the angle should I have any other problems. Repair took about 1 1/2 hours but wouldn't have taken as long if I didn't have to fight with nut & bolt on the 2nd band.

Remove the bottom panel. Remove the top. Remove the front panel with the door. Romove the two clamps on the boot seal. Remove the old boot seal. Place the new boot seal on the casing around the drum and ensure you put the gasket nozzle and gasket nozzle washer in place. Install the inside gasket clamp with the clamp bolt to the right as you look at it (Note: ensure the nut is over the tab on the boot gasket and stays lined up there as you tighten it. Replace the front panel of the washer and when it is in place put the boot seal on the outside lip (Note: this is the most difficult part as the gaskets does not like to stay in place as you put the outside clamp on. Replace the washer top. Replace the lower panel (Note: while you have the bottom panel off, you may want to clean the debrie trap which is a white pipe and tray that catches stuff that is left in pockets.) For the entire project I used 7mm and 8 mm sockets, flathead screw driver, and a philips head screw drive.

removed the spring-loaded ring around drum seal, removed old lock latch, and installed new lock latch. also, removed old door plunger and installed new one. then re-installed the spring-loaded ring lock around the seal. there were 5 screws and 3 electrical plugs that were easy to remove and re-install. note: i used a black sharpie to mark where the original door plunger was prior to removing the original.

Step 1- pull washer away from wall. Step2- unplug power, shut off water and disconnect lines, and disconnect drain line. Step 3- unscrew 3 screws from bk and 3 screws from behind control panel. Step 4- remove back of control panel and top of washer. Step 5- unplug wires from old valve and plug into new valve to avoid wrong connection take out screw from back releasing old valve , insert new valve and put back screw. Step 6 put top of washer and back of control panel on and insert screws. Step 7- reconnect hoses and drain , plug washer in and test. All done. I recommend adjusting to level if necessary at this point before pushing back against wall. Good luck. Hope this helps somebody. Jon