GCK23LASBFCC General Electric Refrigerator - Instructions

Knew the switch was bad. Researched on the internet how to fix. Used a steak knife to pop the old one out, changed the contacts to the new switch and popped it back in. It took longer to open the box than it did to replace the switch. And the part arrived 2 days after I ordered it.

Snapped it into place. Nothing to it!

First, turn off power - since I did not want to pull the refrigerator out on my wood floor I tripped the circuit breaker to that circuit and opened door to make sure interior light was off (ensuring power was off). This unit has a bottom freezer, I took out all shelves, ice maker and all parts in the way of accessing back of interior of freezer section. Removed back plastic section by removing one screw in middle top of back panel and prying it out. This was a bit difficult as it was in there a bit tight but once the plastic warmed up it pulled out ok. This revealed the compressor section and temp sensor that was attached to the copper coils with of all things - a zip tie! In pictures of this that I looked at on various web sites the sensor was on a metal bracket attached to the coil so it made me wonder if tf the factory took a shortcut? I cut the old sensor wire, stripped the two wires 1/2", and connected them to the new sensor wire with butt connectors, I put some silicone into the ends of the butt connectors to prevent moisture from entering into connectors and wrapped the connection in black electrical tape. I then "attached" the sensor to the coil using a zip tie, put the plastic back piece back on, inserted everything I took out and put power back to refrigerator. It's been 3 days and temp of refrigerator is stable, ice maker not clogging up, and compressor not running all the time! So far so good.

First I removed the ice tray rack lifting it out of the way to reach the back cover of the fan. Then, the whole back inside panel had to be removed. Two screws removed the fan and bracket from the freezer unit. The missing bumper lid just snapped into place. Replaced everything in reverse order. Pretty easy job.

I just snapped in the new side to the shelf ...very simple and easy:-)

removed 6 screws and repaced cover.

Replaced both the Defrost Thermostat and Defrost Heating Element. The You Tube repair video clips were extremely helpful for both operations. My difficulty was getting access to the parts that needed to be replaced in a very tight side by side freezer space. Otherwise, the repair went smoothly and the refrigerator is back in normal operation in time to save the perishable food inside.

Uncovering the motor is the most difficult part. Installation is stupid-easy. Put all of the coverings back on in reverse order to the way they were removed. I don't think the ice maker has to come out but we weren't using it so it came out first.

You guys ought to win some sort of website Emmy. I found your site as I was searching for a new motherboard, thinking this was the cause of the temperature control problem. I took the time to go through the little diagnostic process you offer and I discovered that the much less expensive defrost thermostat was more often the root cause of the problem ($8 vs $160 for the new motherboard). The part arrived within 3 days and the installation video was enormously helpful. Removal of the rear panel was more difficult than suggested on the video. I'd suggest removing the freezer light fixture before trying to remove the panel as it is nearly impossible to bend the metal panel around the light bulb bases. Anyway, the whole job cost me about $16 for parts and delivery and the fridge is running fine. The combination of the diagnostic tool and the installation video were fantastic...far beyond expectations.

Must have spent 10+ hours solid looking up info on the internet. Our ice maker had broken years ago, the door flap had broken years ago and I thought this was the end of a fridge after just 6 years 8 months.

GE offered a "broken appliance" warranty for $379 for one year, with no guarantee that when a technician came to look at it, the repairs would be covered by the warranty!!! No thank you, you just want me to buy a new fridge. Okay, challenge on, I'll fix it myself.

I took everything from the back of the freezer out. Spent an hour defrosting (note: use hair dryer next time). Ruled out a motherboard problem (even though it appears I have the old style motherboard), removed dust build up from fan intake. I could not get the heater to come on, so I cut off the thermostat defroster and connected the wires together. The only way to get the heater on was to set the freezer control to 0 / zero.

So, ordered part from partselect.com and it arrived the next day!!!. Installed and unit appears to be defrosting okay after a week.

So now I'm back to order the ice maker part. The door flap will wait for another time.

Note: I've put in the time for novices and recognizing how the freezer is constructed.

Time includes taking everything out of the freezer section, unscrewing everything, diagnosing problem, fixing the problem, putting everything back. I would say allow 3-4 hours and pat yourself on the back if you do it quicker.

Note#2, if you have a large build up there is a hole in the floor of the freezer section. If the water does not evaporate it will run out of the hole and into your wooden floors! Place towels both inside and outside the unit just in case!

I have not yet done the repair. After watching this repair video two problems came to mind. First I only ordered one grommet not knowing that there were two (or more I don't yet know). The second problem is that this video must be for a fridge from like the 1940, but it looks NOTHING like mine from 2008. The manual shows a bazillion parts and frankly I'm just a wee bit afraid to get started, and I am generally very handy, buuuttttttttt I don't know about this one

+The shelf face has little plastic locator clips that snapped off. the shelf face just comes off with a light lift of these two clips and a slight upward pull then lift up and off. The new one slips on with the top slipping onto the top rail of shelf, then push the bottom tow clips over the bottom rail of the shelf. There you have it smooth as glass.

Replaced Temperature Sensor and now it is getting cold.

take the metal cover off the defrost thermostat is on top of the coil take the thermostat off from the coil cut the two wires take the wire and strip the ends off take the new thermostat the wires are color coded wire them together put the thermostat back on coil your done real easy

I followed the video for my model refrigerator on parts select. My hint: when returning the back panel of the freezer, it's slightly adjustable left and right to avoid grazing the fan.